Pinpoint Test L - DTC: B00C5:11, B00C5:12, B00C5:13 and B00C5:1D

Refer to Supplemental Restraint System for schematic and connector information.

Normal Operation and Fault Conditions 

The RCM monitors the passenger seat position sensor circuits for the following faults:

• Open circuit
• Short to voltage
• Short to ground
• Current out of range
• Faulted passenger seat position sensor

If a fault is detected, the RCM stores DTC B00C5:11, B00C5:12, B00C5:13 or B00C5:1D in memory and sends a message to the IPC to illuminate the airbag warning indicator.

DTC Fault Trigger Conditions 

Possible Causes 

• Wiring, terminals or connectors
• Passenger seat position sensor
• RCM

Visual Inspection and Diagnostic Pre-checks 

• Inspect for a damaged passenger seat position sensor.
• Inspect for damaged wiring harness(es).
• Inspect for loose or damaged connectors.

PINPOINT TEST A : B00C5:11, B00C5:12, B00C5:13 AND B00C5:1D 

1. WARNING: Incorrect repair techniques or actions can cause an accidental Supplemental Restraint System (SRS) deployment. Never compromise or depart from these instructions. Failure to precisely follow all instructions could result in serious personal injury from an accidental deployment.
2. NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test.
3. NOTE: Only disconnect or reconnect SRS components when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS.
4. NOTE: Always make sure the correct SRS component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford parts catalog to make sure the correct component is being installed. If an incorrect SRS component is installed, Diagnostic Trouble Codes (DTCs) may set.
5. NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
6. A1 RETRIEVE RCM (RESTRAINTS CONTROL MODULE) DIAGNOSTIC TROUBLE CODES (DTCS)
   
   
   • WARNING: Before beginning any service procedure, refer to Safety Warnings in General Information. Failure to follow this instruction may result in serious personal injury.

     REFER to: Pyrotechnic Device Health and Safety Precautions .

   • Ignition ON.
   • Using a diagnostic scan tool, perform RCM self-test.

   Was DTC B00C5:11, B00C5:12, B00C5:13 or B00C5:1D retrieved on-demand during self-test? 

   Yes	This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test. For DTC B00C5:11 or B00C5:1D, GO to  A2For DTC B00C5:12, GO to  A4For DTC B00C5:13, GO to  A5

   No	This is an intermittent fault when present as a Continuous Memory Diagnostic Trouble Code (CMDTC) only. GO to  A10

7. A2 CHECK THE PASSENGER SEAT TRACK POSITION RESTRAINTS SENSOR DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE (SHORT TO GROUND OR CURRENT OUT OF RANGE INDICATED)
   
   
   NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.
   • Ignition OFF.
   • Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering .
   • Disconnect Passenger Seat Position Sensor (Inline) C3007C .
   • Repower the SRS. Refer to: Supplemental Restraint System (SRS) Repowering .
   • Ignition ON.
   • Using a diagnostic scan tool, perform RCM self-test.
   • DIAGNOSTIC TIP:  When viewing Diagnostic Trouble Codes (DTCs) with the passenger seat position sensor disconnected, an open circuit fault is normally retrieved. Due to the inline seat connector being disconnected, Diagnostic Trouble Codes (DTCs) also set for the passenger safety belt buckle switch, OCS and passenger side airbag.

   Did the on-demand DTC change from B00C5:11 or B00C5:1D to B00C5:13? 

   Yes

   GO to  A8

   No	For DTC B00C5:11, GO to  A3For DTC B00C5:1D, GO to  A9

8. A3 CHECK THE PASSENGER SEAT POSITION SENSOR CIRCUIT FOR A SHORT TO GROUND
   
   
   • Ignition OFF.
   • Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering .
   • Disconnect RCM C310A and C310B .
   • Measure:

     Positive Lead	Measurement / Action	Negative Lead
     C3007C-1	Courtesy of FORD MOTOR COMPANY	Ground

   Is the resistance greater than 10, 000 ohms? 

   Yes

   GO to  A9

   No	REPAIR the circuit. Refer to Connector Repair Procedures for schematic and connector information. Go to  A11

9. A4 CHECK THE PASSENGER SEAT POSITION SENSOR CIRCUIT FOR A SHORT TO VOLTAGE
   
   
   • Ignition OFF.
   • Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering .
   • Disconnect RCM C310A and C310B .
   • Disconnect Passenger Seat Position Sensor (Inline) C3007C .
   • Repower the SRS.

     Do not  prove out the SRS at this time. Refer to: Supplemental Restraint System (SRS) Repowering .

   • Ignition ON.
   • Measure:

     Positive Lead	Measurement / Action	Negative Lead
     C3007C-1	Courtesy of FORD MOTOR COMPANY	Ground

   Is any voltage present? 

   Yes	REPAIR the circuit. Refer to Connector Repair Procedures for schematic and connector information. Go to  A11

   No

   GO to  A9

10. A5 CHECK THE PASSENGER SEAT TRACK POSITION RESTRAINTS SENSOR DTC (DIAGNOSTIC TROUBLE CODE) FOR A FAULT STATUS CHANGE (OPEN INDICATED)
    
    
    NOTE: This pinpoint test step attempts to change the fault reported by the RCM by inducing a different fault condition. If the reported fault changes, this indicates the RCM is functioning correctly and is not the source of the fault.
    • Ignition OFF.
    • Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering .
    • Disconnect Passenger Seat Position Sensor (Inline) C3007C .
    • Connect a fused jumper wire:

      Lead 1	Measurement / Action	Lead 2
      C3007C-1	Courtesy of FORD MOTOR COMPANY	C3007C-2

    • Repower the SRS.

      Do not  prove out the SRS at this time. Refer to: Supplemental Restraint System (SRS) Repowering .

    • Ignition ON.
    • Using a diagnostic scan tool, perform RCM self-test to retrieve Diagnostic Trouble Codes (DTCs).
    • DIAGNOSTIC TIP:  When viewing Diagnostic Trouble Codes (DTCs) with the passenger seat position sensor circuits shorted together, a short to ground fault is normally retrieved. Due to the inline seat connector being disconnected, Diagnostic Trouble Codes (DTCs) will also set for the passenger safety belt buckle switch, OCS and passenger side airbag.

    Did the on-demand DTC change from B00C5:13 to B00C5:11? 

    Yes	REMOVE the fused jumper wire and GO to  A8

    No	REMOVE the fused jumper wire and GO to  A6

11. A6 CHECK THE PASSENGER SEAT POSITION SENSOR CIRCUIT FOR AN OPEN
    
    
    • Ignition OFF.
    • Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering .
    • Disconnect RCM C310A and C310B .
    • Measure:

      Positive Lead	Measurement / Action	Negative Lead
      C310B-24	Courtesy of FORD MOTOR COMPANY	C3007C-1

    Is the resistance less than 0.5 ohm? 

    Yes

    GO to  A7

    No	REPAIR the circuit. Refer to Connector Repair Procedures for schematic and connector information. Go to  A11

12. A7 CHECK THE PASSENGER SEAT POSITION SENSOR GROUND CIRCUIT FOR AN OPEN
    
    
    • Measure:

      Positive Lead	Measurement / Action	Negative Lead
      C3007C-2	Courtesy of FORD MOTOR COMPANY	C310B-53

    Is the resistance less than 3 ohms? 

    Yes

    GO to  A9

    No	REPAIR the circuit. Refer to Connector Repair Procedures for schematic and connector information. Go to  A11

13. A8 CONFIRM THE PASSENGER SEAT POSITION SENSOR FAULT
    
    
    NOTE: Make sure all SRS components and the RCM electrical connectors are connected before carrying out the self-test. If not, Diagnostic Trouble Codes (DTCs) will be recorded.
    • Ignition OFF.
    • Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering .
    • Prior to reconnecting any previously disconnected SRS component:
      • inspect connector(s) (including any inline connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damaged, pinched, cut or pierced wires.
      • inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.
      • repair any concerns found. Refer to Connector Repair Procedures for schematic and connector information.
    • Connect RCM C310A and C310B .
    • Connect Passenger Seat Position Sensor (Inline) C3007C .
      • Tighten to 1 Nm (9 lb-in).
    • Repower the SRS.

      Do not  prove out the SRS at this time. Refer to: Supplemental Restraint System (SRS) Repowering .

    • Ignition ON.
    • Using a diagnostic scan tool, perform RCM self-test.

    Was the original DTC retrieved on-demand during self-test? 

    Yes

    REMOVE and INSPECT the passenger seat position sensor jumper harness for damage. If a concern is found, REPAIR the harness as necessary. Refer to Connector Repair Procedures for schematic and connector information. Go to  A11If a concern is not found in the harness, INSTALL a new passenger seat position sensor. Refer to: Seat Position Sensor . Go to  A11

    No	In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to  A10

14. A9 CONFIRM THE RCM (RESTRAINTS CONTROL MODULE) FAULT
    
    
    NOTE: Make sure all SRS components and the RCM electrical connectors are connected before carrying out the self-test. If not, Diagnostic Trouble Codes (DTCs) will be recorded.
    • Ignition OFF.
    • Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering .
    • Prior to reconnecting any previously disconnected SRS component:
      • inspect connector(s) (including any inline connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damaged, pinched, cut or pierced wires.
      • inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.
      • repair any concerns found. Refer to Connector Repair Procedures for schematic and connector information.
    • Connect RCM C310A and C310B .
    • Connect Passenger Seat Position Sensor (Inline) C3007C .
      • Tighten to 1 Nm (9 lb-in).
    • Repower the SRS.

      Do not  prove out the SRS at this time. Refer to: Supplemental Restraint System (SRS) Repowering .

    • Ignition ON.
    • Using a diagnostic scan tool, perform RCM self-test.

    Was the original DTC retrieved on-demand during self-test? 

    Yes	CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new RCM. Refer to: Restraints Control Module (RCM) . Go to  A11

    No	In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to  A10

15. A10 CHECK FOR AN INTERMITTENT FAULT
    
    
    • Ignition OFF.
    • Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering .
    • Disconnect RCM C310A and C310B .
    • Disconnect Passenger Seat Position Sensor (Inline) C3007C .
      • Inspect connector(s) (including any inline connectors) for corrosion, loose or spread terminals and loose or frayed wire connections at terminals.
      • Inspect wire harness for any damage, pinched, cut or pierced wires.
      • Inspect RCM C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation.
      • Repair any concerns found. Refer to Connector Repair Procedures for schematic and connector information.
    • Connect RCM C310A and C310B .
    • Connect Passenger Seat Position Sensor (Inline) C3007C .
      • Tighten to 1 Nm (9 lb-in).
    • Repower the SRS.

      Do not  prove out the SRS at this time. Refer to: Supplemental Restraint System (SRS) Repowering .

    • Ignition ON.
    • Using a diagnostic scan tool, perform RCM self-test.

    Was DTC B00C5:11, B00C5:12, B00C5:13 or B00C5:1D retrieved on-demand during self-test? 

    Yes	This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test. For DTC B00C5:11 or B00C5:1D, GO to  A2For DTC B00C5:12, GO to  A4For DTC B00C5:13, GO to  A5

    No	The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. Install SRS components only when directed to do so in the pinpoint test. GO to  A11

16. A11 CHECK FOR ADDITIONAL SRS (SUPPLEMENTAL RESTRAINT SYSTEM) DIAGNOSTIC TROUBLE CODES (DTCS)
    
    
    • Ignition OFF.
    • Depower the SRS. Refer to: Supplemental Restraint System (SRS) Depowering .
    • Reconnect all SRS components (if previously disconnected).
      • For Passenger Seat Position Sensor (Inline) C3007C , tighten to 1 Nm (9 lb-in).
    • Repower the SRS.

      Do not  prove out the SRS at this time. Refer to: Supplemental Restraint System (SRS) Repowering .

    • Ignition ON.
    • NOTE: When selecting Restraints from the Self Test menu, DTCs are retrieved from the RCM and OCSM.

      Using a diagnostic scan tool, perform

      Restraints  self-test.

    Are any RCM and/or OCSM Diagnostic Trouble Codes (DTCs) retrieved on-demand during self-test? 

    Yes	Do not clear any Diagnostic Trouble Codes (DTCs) until all Diagnostic Trouble Codes (DTCs) have been resolved. DIAGNOSE and REPAIR the RCM and/or OCSM Diagnostic Trouble Codes (DTCs). Refer to: Airbag Supplemental Restraint System (SRS) .

    No	The repair is complete. RETURN the vehicle to the customer.