Pinpoint Test Ar: U0131:87

AR1 VERIFY THE CUSTOMER CONCERN
- Ignition ON.
- Verify there is an observable symptom present.
Is an observable symptom present?
- Yes : GO to AR3
- No : The system is operating normally at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.
AR2 CHECK FOR ANY RECENT PMI (PROGRAMMABLE MODULE INSTALLATION) CHANGES
- Check the vehicle service history for recent service actions related to the IPC or the PSCM .
Have there been any recent service actions with either module?
- Yes : CARRY out a manual PMI on the applicable module using As-Built data.
- No : GO to AR3
AR3 CHECK THE COMMUNICATION NETWORK
- Ignition ON.
- Using a diagnostic scan tool, perform a network test.
Does the PSCM pass the network test?
- Yes : GO to AR4
- No : REFER to: COMMUNICATIONS NETWORK .
AR4 PERFORM THE PSCM (POWER STEERING CONTROL MODULE) SELF-TEST
- Using a diagnostic scan tool, perform the PSCM self-test.
Are any Diagnostic Trouble Codes (DTCs) recorded?
- Yes : REFER to: POWER STEERING .
- No : GO to AR5
AR5 PERFORM THE IPC (INSTRUMENT PANEL CLUSTER) SELF-TEST
- Using a diagnostic scan tool, perform the IPC self-test.
Are any Diagnostic Trouble Codes (DTCs) recorded?
- Yes : For DTC U3006: 16, GO to PINPOINT TEST AW
  For DTC U3006:17, GO to PINPOINT TEST AX
  
  For all other Diagnostic Trouble Codes (DTCs), REFER to DTC CHART: IPC .
- No : GO to AR5
AR6 RECHECK THE IPC (INSTRUMENT PANEL CLUSTER) DIAGNOSTIC TROUBLE CODES (DTCS)
NOTE: If new modules were installed prior to the DTC being set, the module configuration can be incorrectly set during the PMI or the PMI may not have been carried out.
- Clear the Diagnostic Trouble Codes (DTCs).
- Wait 10 seconds.
- Using a diagnostic scan tool, perform the IPC self-test.
Is DTC U0131:87 still present?
- Yes : GO to AR7
- No : The system is operating correctly at this time. The DTC may have been set due to high network traffic or an intermittent fault condition.
AR7 CHECK FOR DTC U0131:00 SET IN OTHER MODULES
- Using a diagnostic scan tool, clear all Diagnostic Trouble Codes (DTCs).
- Ignition OFF.
- Ignition ON.
- Wait 10 seconds.
- Using a diagnostic scan tool, perform the continuous memory self-test.
- Retrieve the Continuous Memory Diagnostic Trouble Codes (CMDTCs) from all modules.
Is DTC U0131:00 set in the ABS module?
- Yes : GO to AR8
- No : GO to AR9
AR8 CHECK FOR CORRECT PSCM (POWER STEERING CONTROL MODULE) OPERATION
- Ignition OFF.
- Disconnect and inspect the PSCM connectors.
- Repair:
  - corrosion (install new connector or terminals - clean module pins)
  - damaged or bent pins - install new terminals/pins
  - pushed-out pins - install new pins as necessary
- Reconnect the PSCM connectors. Make sure they seat and latch correctly.
- Operate the system and determine if the concern is still present.
Is the concern still present?
- Yes : CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new PSCM (part of the steering column).
  REFER to: STEERING COLUMN .
- No : The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.
AR9 CHECK FOR CORRECT IPC (INSTRUMENT PANEL CLUSTER) OPERATION
- Ignition OFF.
- Disconnect and inspect the IPC connectors.
- Repair:
  - corrosion (install new connector or terminals - clean module pins)
  - damaged or bent pins - install new terminals/pins
  - pushed-out pins - install new pins as necessary
- Reconnect the IPC connectors. Make sure they seat and latch correctly.
- Operate the system and determine if the concern is still present.
Is the concern still present?
- Yes : CHECK OASIS for any applicable Technical Service Bulletins (TSBs). If a TSB exists for this concern, DISCONTINUE this test and FOLLOW TSB instructions. If no Technical Service Bulletins (TSBs) address this concern, INSTALL a new IPC .
  REFER to: INSTRUMENT PANEL CLUSTER (IPC) .
- No : The system is operating correctly at this time. The concern may have been caused by module connections. ADDRESS the root cause of any connector or pin issues.