Pinpoint Test Ah: The Safety Belt Warning Chime Or The Belt-Minder® Chime Is Inoperative

AH1 CHECK THE HEADLAMPS ON WARNING CHIME OPERATION
- Ignition OFF.
- Close the LH front door.
- Place the headlamp switch in the HEADLAMP or PARKING LAMP position.
- Open the driver front door and observe the headlamps on warning chime operation.
- Turn the headlamps/parklamps off.
Does the headlamps on warning chime sound with the headlamps/parking lamps on and the LH front door open and turn off with the headlamps/parking lamps off?
1. Yes : For the Belt-Minder®, GO to AH2
  For the safety belt warning chime, GO to AH3
2. No : INSTALL a new IPC .
  REFER to: Instrument Panel Cluster (IPC) .
AH2 CHECK THE SPEEDOMETER OPERATION
- Ignition ON.
- Verify the speedometer operates.
Does the speedometer operate?
1. Yes : GO to AH3
2. No : GO to PINPOINT TEST C
AH3 PERFORM THE INSTRUMENT PANEL CLUSTER (IPC) SELF-TEST
- Using a scan tool, perform the IPC self-test.
Are any Diagnostic Trouble Codes (DTCs) recorded?
1. Yes : REFER to DTC CHART: IPC .
2. No : GO to AH4
AH4 PERFORM THE GATEWAY MODULE (GWM) SELF-TEST
- Using a scan tool, perform the GWM self-test.
Are any Diagnostic Trouble Codes (DTCs) recorded?
1. Yes : REFER to: COMMUNICATIONS NETWORK .
2. No : GO to AH5
AH5 PERFORM THE POWERTRAIN CONTROL MODULE (PCM) SELF-TEST
- Using a scan tool, perform the PCM self-test.
Are any Diagnostic Trouble Codes (DTCs) recorded?
1. Yes : REFER to: ELECTRIC POWERTRAIN CONTROL .
2. No : GO to AH6
AH6 PERFORM THE BODY CONTROL MODULE (BCM) SELF-TEST
- Using a scan tool, perform the BCM self-test.
Are any Diagnostic Trouble Codes (DTCs) recorded?
1. Yes : REFER to: BODY CONTROL MODULE (BCM) .
2. No : GO to AH7
AH7 PERFORM THE RESTRAINTS CONTROL MODULE (RCM) SELF-TEST
- Using a scan tool, perform the RCM self-test.
Are any Diagnostic Trouble Codes (DTCs) recorded?
1. Yes : REFER to: AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) - VEHICLES BUILT FROM: 11-JUNE-2012 .
2. No : GO to AH8
AH8 CHECK THE DRIVER AND FRONT PASSENGER SAFETY BELT BUCKLE SWITCH
- Using a scan tool, monitor the RCM driver and front passenger safety belt buckle Parameter Identifications (PIDs) (SBELT_D_ST) and (SBLT_P_ST) while buckling and unbuckling the safety belt.
Do the Parameter Identifications (PIDs) display BUCKLED with the safety belt buckled and UNBUCKLED with the safety belt unbuckled?
1. Yes : GO to AH9
2. No : INSTALL a new safety belt buckle.
  REFER to: FRONT SAFETY BELT BUCKLE - VEHICLES BUILT FROM: 11-JUNE-2012 .
AH9 CHECK THE BELT-MINDER® CONFIGURATION
NOTE: Verify that an administrator key is used for this test and not a MyKey® programmed key. When a MyKey® programmed key is used, the Belt-Minder® is automatically turned on and cannot be disabled (if previously disabled by an administrator, the Belt-Minder® remains disabled when an administrator key is used).
- Verify the Belt-Minder® is activated or configured on for the seating position in question.
  REFER to: SAFETY BELT MINDER DEACTIVATING/ACTIVATING .
Is the Belt-Minder activated for the seating position in question?
1. Yes : If the Belt-Minder® is always on above 10 km/h (6 mph) with the safety belt unfastened, the system is operating correctly. If the Belt-Minder® is always on with the safety belt fastened or never on with the safety belt unfastened above 10 km/h (6 mph), INSTALL a new RCM .
  REFER to: RESTRAINTS CONTROL MODULE (RCM) .
2. No : ACTIVATE the Belt-Minder® for the seating position in question.
  REFER to: SAFETY BELT MINDER DEACTIVATING/ACTIVATING .