LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 2339 (Anti-Lock Brake System - Vehicle Dynamic Systems) >> Diagnosis And Testing >> Anti-Lock Control - Hybrid >> Pinpoint Tests >> Pinpoint Test R: DTC C0031:01; C0034:01; C0037:01 or C003A:01 >> Pinpoint Test R: DTC C0031:01; C0034:01; C0037:01 Or C003A:01

Pinpoint Test R: DTC C0031:01; C0034:01; C0037:01 Or C003A:01

WARNING: This page is about a different car, the 2010 Mercury Milan, 2010 Lincoln MKZ, and 2010 Ford Fusion. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Use the Flex Probe Kit for all test connections to prevent damage to the wiring terminals. Do not use standard multimeter probes.
  1. R1 VERIFY ALL WIRING CONNECTIONS 
    • Disconnect: ABS Module C135.
    • Disconnect: Suspect Wheel Speed Sensor.
    • Using a good light source, inspect each connector terminal for any corrosion.
    • Inspect both connectors for any pushed-out pins.

      Refer to the appropriate SYSTEM WIRING DIAGRAMS article for schematic and connector information.

    • Using a suitable mating terminal, check each female terminal for deformed or enlarged contacts by comparing the mating terminal's fit between each of the following pins:
      • C135-33
      • C135-34
      • C135-36
      • C135-37
      • C135-42
      • C135-43
      • C135-45
      • C135-46
      • Suspect wheel speed sensor, pin-1
      • Suspect wheel speed sensor, pin-2 (front sensor) or pin-3 (rear sensor)
      Fig 1: Identifying C135 Connector Terminals
      G06257097Courtesy of FORD MOTOR CO.
    • Refer to the appropriate SYSTEM WIRING DIAGRAMS article for schematic and connector information.
    • Is each terminal free of corrosion, pushed-out pins or spread terminals? 
    • Yes:  GO to  R2.
    • No:  REPAIR the affected terminal(s). CLEAR the DTCs. REPEAT the self-test.
  2. R2 CHECK FOR FAULT REPEATABILITY 
    • Connect: ABS Module C155.
    • Connect: Suspect Wheel Speed Sensor.
    • Connect the scan tool.
    • Ignition ON.
    • Using the scan tool, clear the ABS module DTCs.
    • Drive the vehicle at least 20 km/h (12 mph).
    • Enter the following diagnostic mode on the scan tool: Self Test - ABS Module.
    • Retrieve and record the ABS module DTCs.
    • Are DTCs C0031:01, C0034:01, C0037:01 and/or C003A:01 retrieved? 
    • Yes:  For DTCs C0031:01 and C0034:01, if the Rotunda Active Wheel Speed Sensor Tester is available, GO to R3. If the Rotunda Active Wheel Speed Sensor Tester is not available, GO to  R5.

      For DTCs C0037:01 and C003A:01, GO to  R5.

    • No:  INSPECT the wheel speed sensors, wheel speed sensor wiring and wheel speed sensor tone rings. REPAIR or INSTALL new as necessary. If any other DTCs are retrieved, GO to ABS MODULE DTC TABLE .
  3. R3 CHECK THE ABS MODULE OUTPUT USING THE ROTUNDA ACTIVE WHEEL SPEED SENSOR TESTER 
    NOTE: The front wheel speed sensor electrical connectors are located behind the wheel well splash shields. The rear wheel speed sensor electrical connectors are located under the rear seat cushion.
    • Ignition OFF.
    • Disconnect: Suspect Wheel Speed Sensor.
    • Connect the Rotunda Active Wheel Speed Sensor Tester to the wheel speed sensor connectors.
    • Ignition ON.
    • Select the correct system polarity on the Rotunda Active Wheel Speed Sensor Tester and turn the power switch to the ON position.
    • Is the module output LED illuminated? 
    • Yes:  GO to  R4.
    • No:  GO to  R7.
  4. R4 CHECK THE WHEEL SPEED SENSOR OUTPUT WITH THE ROTUNDA ACTIVE WHEEL SPEED SENSOR TESTER 
    • Raise the suspect wheel until it can spin freely. Refer to JACKING & LIFTING .
    • While monitoring the Rotunda Active Wheel Speed Sensor Tester, slowly spin the suspect wheel.
    • Do the sensor output LEDs illuminate and flash and is the current overload LED not illuminated? 
    • Yes:  The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. CLEAR the DTCs. REPEAT the self-test.
    • No:  If the current level LED is not illuminated and the sensor output LEDs do not illuminate or if the current level LED is illuminated red, INSTALL a new wheel speed sensor. REFER to Removal and Installation  or Removal and Installation . CLEAR the DTCs. REPEAT the self-test.

      If the current level LED is not illuminated and the sensor output LEDs illuminate green, but do not flash, INSPECT the wheel speed sensor tone ring and INSTALL new if necessary. If the tone ring is OK, INSTALL a new wheel speed sensor. REFER to Removal and Installation  or Removal and Installation . CLEAR the DTCs. REPEAT the self-test.

  5. R5 CHECK THE WHEEL SPEED SENSOR CIRCUITS FOR A SHORT TO POWER 
    NOTE: No measurements should be taken with the wheel speed sensor connected. Damage to the wheel speed sensor will result.
    NOTE: The front wheel speed sensor electrical connectors are located behind the wheel well splash shields. The rear wheel speed sensor electrical connectors are located under the rear seat cushion.
    • Ignition OFF.
    • Disconnect: ABS Module C135.
    • Disconnect: Suspect Wheel Speed Sensor.
    • Ignition ON.
    • For DTC C0031:01 (LF)  , measure the voltage between ground and:
      • ABS module C135-45, circuit VCA03 (VT/WH), harness side.
      • ABS module C135-46, circuit RCA17 (YE), harness side.
        Fig 2: Measuring Voltage Between Ground & ABS Module C135-45
        G06094498Courtesy of FORD MOTOR CO.
    • For DTC C0034:01 (RF)  , measure the voltage between ground and:
      • ABS module C135-33, circuit RCA19 (VT), harness side.
      • ABS module C135-34, circuit VCA05 (GY/VT), harness side.
      Fig 3: Measuring Voltage Between Ground & ABS Module C135-33
      G06094497Courtesy of FORD MOTOR CO.
    • For DTC C0037:01 (LR)  , measure the voltage between ground and:
      • ABS module C135-36, circuit VCA04 (BU/OG), harness side.
      • ABS module C135-37, circuit RCA18 (BN/GN), harness side.
      Fig 4: Measuring Voltage Between Ground & ABS Module C135-36
      G06094500Courtesy of FORD MOTOR CO.
    • For DTC C003A:01 (RR)  , measure the voltage between ground and:
      • ABS module C135-42, circuit RCA20 (BN), harness side.
      • ABS module C135-43, circuit VCA06 (WH/OG), harness side.
      Fig 5: Measuring Voltage Between Ground & ABS Module C135-42
      G06094499Courtesy of FORD MOTOR CO.
    • Is any voltage present? 
    • Yes:  REPAIR the affected circuit(s). CLEAR the DTCs. REPEAT the self-test.
    • No:  GO to  R6.
  6. R6 CHECK THE WHEEL SPEED SENSOR CIRCUITS FOR A SHORT TO GROUND 
    NOTE: Both circuits must be checked for each DTC.
    • Ignition OFF.
    • For DTC C0031:01 (LF)  , measure the resistance between ground and:
      • ABS module C135-45, circuit VCA03 (VT/WH), harness side.
      • ABS module C135-46, circuit RCA17 (YE), harness side.
      Fig 6: Measuring Resistance Between Ground & ABS Module C135-45
      G06094502Courtesy of FORD MOTOR CO.
    • For DTC C0034:01 (RF)  , measure the resistance between ground and:
      • ABS module C135-34, circuit VCA05 (GY/VT), harness side.
      • ABS module C135-33, circuit RCA19 (VT), harness side.
      Fig 7: Measuring Resistance Between Ground & ABS Module C135-34
      G06094501Courtesy of FORD MOTOR CO.
    • For DTC C0037:01 (LR)  , measure the resistance between ground and:
      • ABS module C135-36, circuit VCA04 (BU/OG), harness side.
      • ABS module C135-37, circuit RCA18 (BN/GN), harness side.
      Fig 8: Measuring Resistance Between Ground & ABS Module C135-36
      G06094504Courtesy of FORD MOTOR CO.
    • For DTC C003A:01 (RR)  , measure the resistance between ground and:
      • ABS module C135-43, circuit VCA06 (WH/OG), harness side.
      • ABS module C135-42, circuit RCA20 (BN), harness side.
      Fig 9: Measuring Resistance Between Ground & ABS Module C135-43
      G06257038Courtesy of FORD MOTOR CO.
    • Are the resistances greater than 10,000 ohms? 
    • Yes:  GO to  R7.
    • No:  REPAIR the affected circuit(s). CLEAR the DTCs. REPEAT the self-test.
  7. R7 CHECK THE WHEEL SPEED CIRCUITS FOR AN OPEN 
    NOTE: The front wheel speed sensor electrical connectors are located behind the wheel well splash shields. The rear wheel speed sensor electrical connectors are located under the rear seat cushion.
    • Ignition OFF.
    • Disconnect: ABS Module C135.
    • Disconnect: Suspect Wheel Speed Sensor.
    • Measure the resistance between ABS module connector C135, harness side and the suspect wheel speed sensor connector, harness side as indicated in the following table below:
      ABS MODULE SPECIFICATIONS TABLE

      ABS Module Circuit Wheel Speed Sensor
      DTC C0031:01 (LF) 
      C135-45 VCA03 (VT/WH) C150-1
      C135-46 RCA17 (YE) C150-2
      DTC C0034:01 (RF) 
      C135-34 VCA05 (GY/VT) C160-1
      C135-33 RCA19 (VT) C160-2
      DTC C0037:01 (LR) 
      C135-36 VCA04 (BU/OG) C440-3
      C135-37 RCA18 (BN/GN) C440-1
      DTC C003A:01 (RR) 
      C135-43 VCA06 (WH/OG) C426-3
      C135-42 RCA20 (BN) C426-1
      Fig 10: Identifying C135 & C426 Connector Terminals
      G06257040Courtesy of FORD MOTOR CO.
    • Are the resistances less than 5 ohms? 
    • Yes:  GO to  R8.
    • No:  REPAIR the affected circuit(s). CLEAR the DTCs. REPEAT the self-test.
  8. R8 CHECK FOR SHORTED WHEEL SPEED SENSOR CIRCUITS 
    • For DTC C0031:01 (LF)  , measure the resistance between:
      • LF wheel speed sensor C150-1, circuit VCA03 (VT/WH), harness side and LF wheel speed sensor C150-2, circuit RCA17 (YE), harness side.
      Fig 11: Measuring Resistance Between LF Wheel Speed Sensor C150-1 & LF Wheel Speed Sensor C150-2
      G06257041Courtesy of FORD MOTOR CO.
    • For DTC C0034:01 (RF)  , measure the resistance between:
      • RF wheel speed sensor C160-1, circuit VCA05 (GY/VT), harness side and RF wheel speed sensor C160-2, circuit RCA19 (VT), harness side.
      Fig 12: Measuring Resistance Between RF Wheel Speed Sensor C160-1 & RF Wheel Speed Sensor C160-2
      G06257041Courtesy of FORD MOTOR CO.
    • For DTC C0037:01 (LR)  , measure the resistance between:
      • LR wheel speed sensor C440-3, circuit VCA04 (BU/OG), harness side and LR wheel speed sensor C440-1, circuit RCA18 (BN/GN), harness side.
      Fig 13: Measuring Resistance Between LR Wheel Speed Sensor C440-3 & LR Wheel Speed Sensor C440-1
      G06257044Courtesy of FORD MOTOR CO.
    • For DTC C003A:01 (RR)  , measure the resistance between:
      • RR wheel speed sensor C426-3, circuit VCA06 (WH/OG), harness side and RR wheel speed sensor C426-1, circuit RCA20 (BN), harness side.
      Fig 14: Measuring Resistance Between RR Wheel Speed Sensor C426-3 & RR Wheel Speed Sensor C426-1
      G06257044Courtesy of FORD MOTOR CO.
    • Is the resistance greater 10,000 ohms? 
    • Yes:  GO to  R9.
    • No:  REPAIR the affected circuit(s). CLEAR the DTCs. REPEAT the self-test.
  9. R9 CHECK FOR CORRECT ABS MODULE OUTPUT 
    • Connect: ABS Module C135.
    • Ignition ON.
    • For DTC C0031:01 (LF)  , measure the voltage between:
      • LF wheel speed sensor C150-1, circuit VCA03 (VT/WH), harness side and LF wheel speed sensor C150-2, circuit RCA17 (YE), harness side.
      Fig 15: Measuring Voltage Between LF Wheel Speed Sensor C150-1 & LF Wheel Speed Sensor C150-2
      G06257111Courtesy of FORD MOTOR CO.
    • For DTC C0034:01 (RF)  , measure the voltage between:
      • RF wheel speed sensor C160-1, circuit VCA05 (GY/VT), harness side and RF wheel speed sensor C160-2, circuit RCA19 (VT), harness side.
      Fig 16: Measuring Voltage Between RF Wheel Speed Sensor C160-1 & RF Wheel Speed Sensor C160-2
      G06257111Courtesy of FORD MOTOR CO.
    • For DTC C0037:01 (LR)  , measure the voltage between:
      • LR wheel speed sensor C440-3, circuit VCA04 (BU/OG), harness side and LR wheel speed sensor C440-1, circuit RCA18 (BN/GN), harness side.
      Fig 17: Measuring Voltage Between LR Wheel Speed Sensor C440-3 & LR Wheel Speed Sensor C440-1
      G06257047Courtesy of FORD MOTOR CO.
    • For DTC C003A:01 (RR)  , measure the voltage between:
      • RR wheel speed sensor C426-3, circuit VCA06 (WH/OG), harness side and RR wheel speed sensor C426-1, circuit RCA20 (BN), harness side.
      Fig 18: Measuring Voltage Between RR Wheel Speed Sensor C426-3 & RR Wheel Speed Sensor C426-1
      G06257047Courtesy of FORD MOTOR CO.
    • Is the voltage greater than 10 volts? 
  10. R10 CHECK FOR CORRECT ABS MODULE OPERATION 
    • Disconnect: ABS Module C135.
    • Check for:
      • corrosion
      • pushed-out pins
      • spread terminals
    • Connect: ABS Module C135.
    • Make sure the connector is seated correctly, then operate the system and verify the concern is still present.
    • Is the concern still present? 
    • Yes:  INSTALL a new ABS module. REFER to Removal and Installation . TEST the system for normal operation.
    • No:  The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. CLEAR the DTCs. REPEAT the self-test.
scientia non olet · About LEMON Manuals