Fastener Specifications (Off Vehicle)
WARNING: This page is about a different variant/trim than selected.
Single Use Non-Threaded Fasteners/Components
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
|---|
| Application |
| 1-2-3-4-5-Reverse Clutch Piston Dam Inner Seal |
| 1-2-3-4-5-Reverse Clutch Piston Dam Retaining Ring |
| 1-2-3-4-5-Reverse Clutch Piston Dam Seal |
| 1-2-3-4-5-Reverse Clutch Piston Inner Seal |
| 1-2-3-4-5-Reverse Clutch Piston Seal |
| 1-2-3-4-5-Reverse Clutch Piston Outer Seal |
| 1-3-5-6-7 Clutch Piston Dam Retaining Ring |
| 1-3-5-6-7 Clutch Piston Dam Seal |
| 1-3-5-6-7 Clutch Piston Seal- Inner |
| 1-3-5-6-7 Clutch Piston Seal- Outer |
| 2-3-4-6-8 Clutch Piston Dam Retaining Ring |
| 2-3-4-6-8 Clutch Piston Dam Seal- Inner |
| 2-3-4-6-8 Clutch Piston Dam Seal- Outer |
| 2-3-4-6-8 Clutch Piston Seal |
| 4-5-6-7-8-Reverse Clutch Piston Dam Retaining Ring |
| 4-5-6-7-8-Reverse Clutch Piston Seal |
| 4-5-6-7-8-Reverse Clutch Piston Stop Seal |
| Automatic Transmission Control Wiring Harness Clip |
| Automatic Transmission Fluid Pump Gasket |
| Automatic Transmission Fluid Pump Seal |
| Automatic Transmission Case Front Cover Seal |
| Automatic Transmission Front Support Cover Gasket |
| Clutch Housing Fluid Passage Seal |
| Control Valve Body Spacer Plate |
| Control Valve Body Spacer Plate Retainer |
| Control Valve Channel Plate Spacer Plate |
| Input Sun Gear Retaining Ring |
| Propeller Shaft Transmission Flange Fluid Seal |
| Turbine Shaft Fluid Seal Ring [7x] |
| Turbine Shaft Fluid Seal Ring |
| Turbine Shaft Retaining Ring |
| Wiring Harness Clip |
Single Use Threaded Fastener/Component Tightening Specifications
|
NOTE:
All fasteners/components listed in this table MUST BE DISCARDED and replaced with NEW after removal. |
||||
|---|---|---|---|---|
| Application | Ref No.* | Quantity | Size | Specification |
| Metric (English) | ||||
| Automatic Transmission Case Front Cover Bolt Refer to procedure for tightening sequence and torque values. |
3 | 11 | M6 x 30 | Transmission Case Front Cover and Drive Link Installation |
| Automatic Transmission Fluid Baffle Bolt | ||||
|
12 | 2 | M6 x 25 | 4 N.m (35 lb in) |
|
45 degrees | |||
| Automatic Transmission Case Front Cover Bolt@Output Speed Sensor | ||||
|
38 | 3 | M6 x 25 | 4 N.m (35 lb in) |
|
45 degrees | |||
| Park Pawl Actuator Bracket Bolt | 606 | 2 | M8 x 35 | 31 N.m (23 lb ft) |
| Propeller Shaft Transmission Flange Nut | 25 | 1 | - | 105 N.m (77 lb ft) |
| *Reference number refers to the component callout number in Disassembled Views | ||||
Reusable Threaded Fastener Tightening Specifications
|
NOTE:
All fasteners listed in this table can be reused after removal. |
||||
|---|---|---|---|---|
| Application | Ref No.* | Quantity | Size | Specification |
| Metric (English) | ||||
| Automatic Transmission Auxiliary Fluid Accumulator Bleeder Valve | 399 | 1 | - | 11 N.m (97 lb in) |
| Automatic Transmission Auxiliary Fluid Accumulator Bolt | 398 | 2 | M4 x 15 | 3 N.m (27 lb in) |
| Automatic Transmission Case Extension Bolt Refer to procedure for tightening sequence and torque values. |
23 | 6 | M10 x 40 | Case Extension Assembly Installation |
| Automatic Transmission Case Extension Hole Plug | 407 | 2 | - | 11 N.m (97 lb in) |
| Automatic Transmission Case Extension Stud | 412 | 2 | - | 15 N.m (11 lb ft) |
| Automatic Transmission Fluid Pan Bolt Refer to procedure for tightening sequence and torque values. |
51 | 15 | M6 x 20 | Transmission Fluid Pan and Filter Assembly Installation |
| Automatic Transmission Fluid Pump Bolt Refer to procedure for tightening sequence and torque values. |
300 | 5 | M6 x 28 | Control Valve Body Assembly Assemble |
| Automatic Transmission Wiring Harness Bracket Bolt | 356 | 1 | M6 x 20 | 9 N.m (80 lb in) |
| Control Valve Channel Plate Bolt Refer to procedure for tightening sequence and torque values. |
314 | 19 | M5 x 55 | Control Valve Body Assembly Assemble |
| Control Valve Channel Plate Bolt Refer to procedure for tightening sequence and torque values. |
321 | 8 | M5 x 45 | Control Valve Body Assembly Assemble |
| Control Valve Lower Body Bolt Refer to procedure for tightening sequence and torque values. |
321 | 3 | M5 x 45 | Control Valve Body Assembly Assemble |
| Control Valve Solenoid Body Bolt Refer to procedure for tightening sequence and torque values. |
44 | 4 | M6 x 45 | Control Valve Assembly and Transmission Wiring Harness Installation |
| Control Valve Solenoid Body Bolt Refer to procedure for tightening sequence and torque values. |
43 | 7 | M6 x 68 | Control Valve Assembly and Transmission Wiring Harness Installation |
| Manual Shift Detent Lever Spring Bolt | 42 | 1 | M6 x 25 | 12 N.m (106 lb in) |
| Stator Shaft Support Bolt Refer to procedure for tightening sequence and torque values. |
17 | 9 | M8 x 33 | Stator Shaft Support Installation |
| Automatic Transmission Fluid Pan Drain Plug | 50 | 1 | - | 9 N.m (80 lb in) |
| *Reference number refers to the component callout number in Disassembled Views | ||||