Dashboard/Steering Hanger Beam Removal/Installation
WARNING: This page is about a different car, the 2011 Honda Insight and 2010 Honda Insight. However, it is still accessible from the selected car via links, so may be relevant.
SRS components are located in this area. Review the SRS component locations (see COMPONENT LOCATION INDEX ) and the precautions and procedures (see PRECAUTIONS AND PROCEDURES ) before doing repairs or service.
NOTE:
- Put on gloves to protect your hands.
- Have an assistant help you when removing and installing the dashboard/steering hanger beam.
- Take care not to scratch the dashboard, body and other related parts.
- Do the 12 volt battery terminal disconnection procedure (see 12 VOLT BATTERY TERMINAL DISCONNECTION AND RECONNECTION ), then wait at least 3 minutes before beginning work.
- Remove these items:
- Front seats, both sides (see FRONT SEAT REMOVAL/INSTALLATION ).
- Driver's dashboard undercover (see DRIVER'S DASHBOARD UNDERCOVER REMOVAL/INSTALLATION ).
- Kick panels, both sides (see TRIM REMOVAL/INSTALLATION - DOOR AREAS ).
- Center console (see CENTER CONSOLE REMOVAL/INSTALLATION ).
- Shift knob and A/T gear position indicator panel (see SHIFT LEVER DISASSEMBLY/REASSEMBLY ).
- Glove box (see GLOVE BOX REMOVAL/INSTALLATION ).
- Fuse access panel (see FUSE ACCESS PANEL REMOVAL/INSTALLATION ).
- Passenger's dashboard undercover (see PASSENGER'S DASHBOARD UNDERCOVER REMOVAL/INSTALLATION ).
- A-pillar trim, both sides (see TRIM REMOVAL/INSTALLATION - PILLAR AREAS ).
- Steering column (see STEERING COLUMN REMOVAL AND INSTALLATION ).
- Disconnect the antenna lead connector (see step 4 under HEADLINER REMOVAL/INSTALLATION
).
Driver's side
- From under the dash, disconnect the right engine compartment wire harness connector (A), the left engine compartment wire harness connectors (B), the driver's side wire harness connectors (C), the driver's door wire harness connectors (D), the roof wire harness connectors (E), and remove the bolt (F), then release the left engine compartment wire harness (G) from the driver's under-dash fuse/relay box (H).
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Center
- From under the dash, disconnect the air hose (A), then remove it.
- Disconnect the A/C wire harness connectors (A).
- Remove the heater joint duct (A).
- From under dash, disconnect the SRS control unit connector (A), the yaw rate-lateral/acceleration sensor (if equipped) (B), the shift lever connector (C), and the driver's side wire harness connector (D). Remove the ground bolt (E) using a TORX T30 bit, and detach the harness clips (F).
Courtesy of AMERICAN HONDA MOTOR CO., INC.
Passenger's side
- From under the dash, disconnect the passenger's door wire harness connector (A), the right engine compartment wire harness connector (B), and the SRS sensor subharness connector (C).
- Detach all of the harness and the connector clips.
- Remove the special bolts (A, B) from outside the passenger's door.
- Remove the caps (C).
- Loosen the special bolts until they disengage from the threads on the hanger beam side bracket (D), and engage the inside threads of the adjusting nuts (E). The thread lock on the special bolts makes the special bolts and the adjusting nuts turn together.
- Continue to loosen the special bolts to turn the adjusting nuts into the sleeves (F) until the nuts bottom out. This creates a gap (G) between the adjusting nuts and the body.
- Loosen the special bolts to disengage them from the adjusting nuts, then remove the bolts.
- If the adjusting nuts (A) are not screwed fully into the fixed space adjuster when removing the special bolts, slightly screw the adjusting nuts into the space adjuster with a 8 mm wrench (B). In this case, the special bolt should be replaced with a new one because its thread locks were worn out.
- From outside the driver's door, remove the caps (A), then remove the bolts (B, C, D).
- Lift up on the dashboard (A) to release it from the guide pins (B, C). Carefully remove the dashboard through the front door opening. Take care not to scratch the body with the adjusting nuts on the passenger's side.NOTE: Do not rest the dashboard on its center console opening, or it may be damaged. Lay it on its front or back.
- Install the dashboard in the reverse order of removal, and note these items:
- Make sure the dashboard fits onto the guide pins correctly.
- Before tightening the bolts, make sure the wire harnesses are not pinched.
- Make sure the connectors are plugged in properly.
- Before reinstalling the dashboard, be sure the adjusting nuts (A) on the passenger's side can be screwed/unscrewed lightly by hand, and then screw them into the sleeves (B) fully by hand. Do not tighten them with any tools.
- Before reinstalling the dashboard, screw the special bolts (C) into the adjusting nuts, and check that they turn together. If they do not turn together, replace the special bolts.
- After setting the dashboard in the body, reinstall all of the mounting bolts but do not tighten them. First tighten the driver's side bracket bolts to the specified torque. Next, tighten the special bolts. As you tighten the bolts, the adjusting nuts screw out of the sleeves until they contact the body. Continue tightening the special bolts to the specified torque.
- Tighten all remaining mounting bolts to the specified torque.
- After tightening both side bracket mounting bolts, tighten the center frame mounting bolts.
- Do the 12 volt battery terminal reconnection procedure (see 12 VOLT BATTERY TERMINAL DISCONNECTION AND RECONNECTION ).
- Check for any DTCs that may have been set during repairs, and clear them.
Special bolt tightening on passenger's side