LEMON Manuals: Even more car manuals for everyone
Home >> Cadillac >> 2021 >> CT4 V, RWD >> Repair and Diagnosis >> Brakes >> Mechanical - Hydraulic >> Hydraulic Brakes >> Repair Instructions >> Brake Pedal Assembly Replacement >> Installation Procedure

Installation Procedure

  1. GM5486242Courtesy of GENERAL MOTORS COMPANY

    Using an assistant to reposition the brake master cylinder - with power brake booster and electronic brake control module, install the brake pedal assembly (3).

    2. CAUTION:

    Refer to Fastener Caution .

  2. Brake Master Cylinder Nut (2) - Install and tighten [2x] - Fastener Specifications 
  3. Brake Pedal Nut (1) - Install and tighten [2x] - Fastener Specifications 
  4. GM5880985Courtesy of GENERAL MOTORS COMPANY

    Engage the brake pedal (1) to the brake master cylinder push rod by pushing inwards.

  5. Ensure the brake pedal retainer is secured by lightly pulling rearward on the brake pedal (1).
  6. GM5333075Courtesy of GENERAL MOTORS COMPANY

    Brake Pedal Position Sensor Electrical Connector (2) - Connect

  7. Retainer (1) - Secure [2x]
  8. GM5644434Courtesy of GENERAL MOTORS COMPANY

    Air Distributor Duct Bolt (1) - Install and tighten - Fastener Specifications

  9. GM5454443Courtesy of GENERAL MOTORS COMPANY

    Serial Data Gateway Bracket (2) - Install

  10. Serial Data Gateway Module Bracket Bolt (1) - Tighten [2x] - Fastener Specifications
  11. Connect and position the wiring harness.
  12. GM5454224Courtesy of GENERAL MOTORS COMPANY
    NOTE:

    Typical wiring harness shown. Individual wiring harnesses may differ based on option content.

    Connect the electrical connectors (1)

  13. Floor Front Air Outlet Duct Bolt (1) - Install and tighten - Fastener Specifications
  14. GM5454049Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Knee Bolster Deflector (2) - Install

  15. Instrument Panel Tie Bar Brace Bolt (1) - Install and tighten [3x] - Fastener Specifications
  16. GM5325852Courtesy of GENERAL MOTORS COMPANY

    Floor Front Air Outlet Duct - Left Side Outer (2) - Install

  17. GM5446428Courtesy of GENERAL MOTORS COMPANY

    Connect and position the wiring harness.

  18. Instrument Panel Knee Bolster (1) - Install
  19. GM5446424Courtesy of GENERAL MOTORS COMPANY

    Data Link Connector Bolt (1) - Install and tighten [2x] - Fastener Specifications

  20. Instrument Panel Knee Bolster Bolt (2) - Install and tighten [3x] - Fastener Specifications
  21. Connect the electrical connector.
  22. GM5433957Courtesy of GENERAL MOTORS COMPANY

    Connect the electrical connector.

  23. Instrument Panel Center Trim Pad (1) - Install
  24. Return the steering column to its original position.
  25. GM5310879Courtesy of GENERAL MOTORS COMPANY

    Connect the electrical connector.

  26. Instrument Panel Lower Trim Panel Insulator (1) - Install
  27. GM5310878Courtesy of GENERAL MOTORS COMPANY

    Install the tabs into the instrument panel lower trim panel insulator (1).

  28. GM5310877Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Lower Trim Panel Insulator Retainer (1) - Install

  29. Instrument Panel Insulator Bolt (2) - Install and tighten [2x] - Fastener Specifications
  30. Instrument Panel Insulator Nut (3) - Install and tighten [2x] - Fastener Specifications
  31. GM5300282Courtesy of GENERAL MOTORS COMPANY

    Attach the hood primary latch release cable end retainer to the hood primary latch release cable handle (1).

  32. GM5421735Courtesy of GENERAL MOTORS COMPANY

    Instrument Panel Outer Trim Cover - Left Side (1) - Install

  33. GM5443235Courtesy of GENERAL MOTORS COMPANY

    Connect the electrical connector.

  34. Instrument Panel Lower Airbag - Driver Side (2) - Install
  35. Instrument Panel Lower Airbag Nut (1) - Install and tighten [2x] - Fastener Specifications
  36. Enable the SIR System. SIR Disabling and Enabling .
  37. Calibrate the brake pedal position sensor. Brake Pedal Position Sensor Calibration
scientia non olet · About LEMON Manuals