Installing fuel delivery line
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2023 BMW M5, 2022 BMW M5, 2021 BMW M5, 2020 BMW M5, and 2019 BMW M5. However, it is still accessible from the selected car via links, so may be relevant.
- Feed in the fuel supply line.
- Tighten union nut (1).
TIGHTENING TORQUES SPECIFICATION
| Fuel supply line/rail to high pressure pump | ||
| Nut | tightening torque | 30 Nm |
- Position wiring harness.
- Engage cable clip (2).
- Tighten down screw (1).
TIGHTENING TORQUES SPECIFICATION
| Wiring harness to cylinder head cover | ||
| M6x16 screw | tightening torque | 10 Nm |
- Tighten the nut (2).
TIGHTENING TORQUES SPECIFICATION
| Ground cable to hold-down device | ||
| Nuts | Tightening torque | 5.5 Nm |
- Tighten down screw (1).
TIGHTENING TORQUES SPECIFICATION
| Wiring harness to cylinder head cover | ||
| M6x16 screw | tightening torque | 10 Nm |
- Tighten union nut (2).
TIGHTENING TORQUES SPECIFICATION
| Fuel supply line/rail to high pressure pump | ||
| Nut | tightening torque | 30 Nm |
TIGHTENING TORQUES SPECIFICATION
| Positive battery cable to alternator | ||
| Nut M8 | Tightening torque | 19 Nm |
- Install the cover (1).
- Position tank vent line.
- Engage holder (2) of the tank vent line.
- Tighten down screw (1).
TIGHTENING TORQUES SPECIFICATION
| Coolant lines to alternator | ||
| M6x16 screw | Tightening torque | 8 Nm |
- Tighten down screws (1).
TIGHTENING TORQUES SPECIFICATION
| Fuel supply line to cylinder head | ||
| Hexagon screw M6x16 | Tightening torque | 10 Nm |
- Position wiring harness.
- Tighten down screw (1).
TIGHTENING TORQUES SPECIFICATION
| Ground cable to hold-down device | ||
| Nuts | Tightening torque | 5.5 Nm |
- Tighten down screws (2).
TIGHTENING TORQUES SPECIFICATION
| Wiring harness to cylinder head cover | ||
| M6x16 screw | tightening torque | 10 Nm |
Follow-up work
- Refer to INSTALLING THE IGNITION COILS OF CYLINDERS 1 AND 2 .
- Refer to INSTALLING THE IGNITION COILS OF CYLINDERS 5 AND 6 .
- Installing holder with the wiring harness for the sensor system of cylinder bank 2.
- Position the holder with the wiring harness for the sensor system.
- Tighten screws (2).
TIGHTENING TORQUES SPECIFICATIONHolder of sensor system M6x16 screw Tightening torque 10 Nm - Connect plug connection (3) and lock.
- Engage the coolant ventilation line in area (1) at the holder.
- Tighten nut (1).
- Refer to INSTALLING THE HOLDER WITH THE VEHICLE WIRING HARNESS FOR THE SENSOR SYSTEM OF CYLINDER BANK 1 .
- Refer to INSTALLING THE RIGHT-HAND CHARGE AIR COOLER .
- Refer to INSTALLING THE LEFT-HAND CHARGE AIR COOLER .
- Refer to INSTALLING OIL FILLER NECK .
- Refer to CLOSING THE COOLANT PUMPS .
- Refer to FILLING THE LOW-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
- Refer to VENTING THE LOW-TEMPERATURE COOLING SYSTEM .
- Refer to INSTALLING THE WHEEL ARCH COVER ON THE FRONT LEFT AND BOTTOM RIGHT .
- Refer to INSTALLING THE STIFFENING PLATE .
- Refer to INSTALLING DRIVE BELT .
- Refer to INSTALLING FAN COWL WITH ELECTRIC MOTOR .
- Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
- Refer to INSTALLING THE CLEAN AIR PIPE OF CYLINDER BANK 2 .
- Refer to INSTALLING RIGHT INTAKE SILENCER HOUSING .
- Refer to INSTALLING LEFT INTAKE SILENCER HOUSING .
- Refer to INSTALLING FRONT CROSS CONNECTION .
- Refer to TIGHTENING THE LEFT FRONT-END STRUT .
- Refer to TIGHTENING THE FRONT-END STRUT ON THE RIGHT .
- Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT ON THE RIGHT .
- Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT ON THE LEFT .
- Refer to INSTALLING COOLANT EXPANSION TANK .
- Refer to INSTALLING HOLDER OF THE DME CONTROL UNIT FOR CYLINDERS 5 TO 8 .
- Installing the cover panel of the master DME control unit.
- Position the cover of the master DME control unit (1)
- Engage the cover panel of the master DME control unit (1) downwards with the clamps (2) and the guide pins (3) in the carrier plate of the DME.
- Refer to INSTALLING THE COVER PANEL OF THE SLAVE DME CONTROL UNIT .