Installing turbocharger

• Check stud bolts (1) for damage and, if necessary, replace stud bolts (1).
• Check insertion depth (A) of stud bolt (1).
  TECHNICAL DATA SPECIFICATIONS
  
  

  Screw-in depth of upper stud bolts on cylinder head
  Dimension A	30 mm

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: RISK OF DAMAGE
  Damage to the surface. 
  The use of metal-cutting tools (e.g., emery cloths) for cleaning surfaces can damage them and lead to leaks and/or engine damage. 

  • Do not use any metal-cutting tools.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Clean the sealing surfaces (1) on the cylinder head using special tool 0 495 1 02 (11 4 470). 
• Replace seals (1).

  Parts:  Seal

  Courtesy of BMW OF NORTH AMERICA, INC.

• (1) Insert and install gaskets.
• Make sure the seals (1) are positioned correctly. 

  Courtesy of BMW OF NORTH AMERICA, INC.

  NOTE: RISK OF DAMAGE
  Damage to the surface. 
  The use of metal-cutting tools (e.g., emery cloths) for cleaning surfaces can damage them and lead to leaks and/or engine damage. 

  • Do not use any metal-cutting tools.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Clean the sealing surfaces on the exhaust turbocharger (1) using special tool 0495 102 (11 4 470). 
  CAUTION: Heavy component. 
  Heavy components can lead to injury or damage. 

  • Remove and install heavy components with the aid of another person/other persons.
• Insert and install the turbocharger (1).
• Protect the turbocharger (1) from falling.

  Courtesy of BMW OF NORTH AMERICA, INC.

• When replacing nut (1), use the changed version of nut (2).

  Courtesy of BMW OF NORTH AMERICA, INC.

• Replace nuts (1).

  Parts:  Nuts

• Insert the nuts (1).
  NOTE: Insert nuts in 360 degree increments.
• Tighten nuts (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Turbocharger to cylinder head
  M7 Replace nuts.	1. Snug torque	5 Nm
  	2. Tightening torque	18 Nm
  	3. Tightening torque	18 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Feed in and install the heat shield (2).
• Replace screws (1).

  Parts:  Screws

• Tighten down screws (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Heat shield of turbocharger to cylinder head top
  M8X12 Replace screws.	tightening torque	19 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Replace screw (1) and (2).

  Parts:  Screws

• Feed in the support (3) and position it.
• Tighten down screws (2).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Turbocharger support to crankcase
  M8x20 Replace screws.	Tightening torque	19 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten down screw (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Turbocharger to support
  M8x25 Replace screw.	Tightening torque	19 Nm

• Replace the sealing rings (1) on the coolant feed line (2) for the turbocharger using the special tool 0 496 714 (00 9 030). 

  Parts:  Sealing ring

  Courtesy of BMW OF NORTH AMERICA, INC.

• Feed in and install the coolant feed line for the turbocharger (3).
• Tighten down screw (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Coolant feed line to crankcase
  M6X12	tightening torque	8 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Tighten down screw (2).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Coolant feed line to crankcase
  M6X12	tightening torque	8 Nm

• Tighten down screw (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Coolant return line holder to crankcase
  M6X12	tightening torque	8 Nm

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect and lock the coolant return line (1).
• Make sure that the coolant return line (1) engages audibly.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Replace the sealing ring on the oil feed line (2) for the turbocharger with the special tool  0 496 714 (00 9 030)  . 

  Parts:  Sealing ring

  NOTE: TECHNICAL INFORMATION 
  Observe the sign in the engine compartment! Only fill with approved engine oil of the correct (Society of Automotive Engineers) visual grade.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Fill the oil feed line (2) for the turbocharger up to the edge with engine oil.
  ENGINE OIL SPECIFICATIONS
  
  

  Technically suitable engine oils for BMW Group engines

• Insert and install the oil supply line (2).
• Tighten down screw (1).
  TIGHTENING TORQUE SPECIFICATIONS
  
  

  Oil feed line for turbocharger to crankcase
  M6x 12 Replace sealing ring	tightening torque	8 Nm

• Connect and lock the connector (1).
• Make sure the connector (1) engages audibly.

  Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to INSTALLING THE OIL RETURN LINE FOR THE TURBOCHARGER .
• Refer to INSTALLING CATALYTIC CONVERTER .
• Refer to INSTALLING EXHAUST SYSTEM .
• Refer to INSTALLING THE LEFT AND RIGHT REAR DIFFUSER .
• Refer to INSTALLING THE TENSION STRUT AT THE RIGHT REAR AND IF NECESSARY, ON THE LEFT SIDE .
• Refer to INSTALLING THE OXYGEN SENSOR MONITOR .
• Refer to INSTALLING LAMBDA OXYGEN SENSOR .
• Refer to INSTALLING THE CLEAN AIR PIPE AND THE RESONATOR .
• Refer to INSTALLING THE INTAKE FILTER HOUSING (TENSION STRUT REMOVED ON SHOCK TOWER) .
• Refer to INSTALLING CHARGE AIR LINE .
• Refer to INSTALLING FAN COWL .
• Refer to INSTALLING THE REAR TOP CROSS CONNECTION .
• Refer to INSTALLING TENSION STRUT ON LEFT AND RIGHT SHOCK TOWER .
• Refer to INSTALLING UPPER CROSS CONNECTION .
• Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT AT TOP LEFT AND RIGHT .
• Refer to FILLING AND VENTING THE HIGH-TEMPERATURE COOLANT CIRCUIT .
• Refer to INSTALLING THE FRONT BOTTOM RIGHT WHEEL ARCH COVER .
• Refer to INSTALLING THE COVER OF THE STEERING ASSEMBLY .
• Refer to INSTALLING FRONT UNDERBODY PROTECTION .
• Refer to INSTALLING THE STIFFENING PLATE .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to CHECKING ENGINE OIL LEVEL .
• Refer to TAKING HOOD OUT OF THE SERVICE POSITION .