Installing the flywheel
NOTE:
TECHNICAL INFORMATION
Clean all threads with a screw tap.
Clean all threads with a screw tap.
- Clean all the screw threads (1).
- Use set of special tools 2 285 058
.
Description Twist drill Thread cutter M12x1.5 Deep stop Screw in tool - Assemble tool set.
Number Description 1 Tool holder 2 Thread cutter M12X1.5 - Mark screwing depth (A) on the thread cutter (1) from the special tool set 2 285 058 with a commercially available tool (2).
TECHNICAL DATA SPECIFICATIONS
| Screw-in depth of thread cutter | |
|---|---|
| Screw-in depth | |
| 18 mm | |
NOTE:
To provide a better overview: Shown with engine removed.
- Screw in the thread cutter (1) from the set of special tools 2 285 058 in arrow direction up to the screw-in depth (2).
TECHNICAL DATA SPECIFICATIONS
| Screw-in depth of thread cutter | |
|---|---|
| Screw-in depth | |
| 18 mm | |
- Make sure that the thread cutter is (1) not pressed up against the timing chain (3).
NOTE:
TECHNICAL INFORMATION
Handle the timing chain carefully to protect the timing chain and timing chain drive from damage.
Handle the timing chain carefully to protect the timing chain and timing chain drive from damage.
- Make sure that the screw-in depth (2) of the screw tap (1) is not exceeded.
The thread cutter (1) must not come into contact with the timing chain (3).
- Note the installation position of the magnet wheel (1).
- Position the magnet wheel (1) on the crankshaft.
- Replace screws (1) to (8).
Parts: Screws
CAUTION:
Heavy component
.
Heavy components can lead to injury or damage .
Heavy components can lead to injury or damage .
- Remove and install heavy components with the aid of another person/other persons.
- Position the flywheel (A).
- Screw in flywheel bolt (1) to (8) by hand.
- Set flywheel (B) with the special tool 0 494 034 (11 9 261) and screw tight with the special tool 0 494 130 (11 9 264) .
- Tighten the flywheel bolts in the sequence (1) to (8) (note the angle of rotation in the next step).
TIGHTENING TORQUE SPECIFICATIONS
| Flywheel to crankshaft | |
|---|---|
| M12x1.5 Replace screws. |
Tightening torque 45 Nm |
| Angle of rotation 45° |
|
- Apply all flywheel bolts (1) with an angle of rotation of 45° by using the special tool 0 490 504 (00 9 120) .
NOTE:
Mark all the flywheel bolts (1) with a vertical line.
- Remove special tool 0 493 938 (11 9 260) .
Follow-up work
- Refer to INSTALLING THE AUTOMATIC TRANSMISSION (ALL-WHEEL DRIVE VEHICLE) (GA8HP75HZ) .
- Refer to FASTENING THE PROP SHAFT (PARTIALLY REMOVED) .
- Refer to INSTALLING TRANSMISSION CROSS MEMBER .
- Refer to INSTALLING THE RETAINING PLATES .
- Refer to INSTALLING THE CONNECTING SUPPORTS ON THE TUNNEL .
- Refer to INSTALLING THE HEAT SHIELDS .
- Refer to INSTALLING CATALYTIC CONVERTER .
- Refer to INSTALLING EXHAUST SYSTEM .
- Refer to INSTALLING FRONT CONNECTING SUPPORT ON TUNNEL .
- Refer to INSTALLING THE LEFT AND RIGHT REAR DIFFUSER .
- Refer to INSTALLING THE RIGHT REAR TENSION STRUT .
- Refer to INSTALLING THE LEFT AND RIGHT UNDERSHIELD (TANK COVER) .
- Refer to INSTALLING THE ACOUSTIC COVER FOR THE OIL SUMP .
- Refer to INSTALLING THE OXYGEN SENSOR MONITOR .
- Refer to INSTALLING LAMBDA OXYGEN SENSOR .
- Refer to INSTALLING THE CLEANING AIR PIPE AND THE RESONATOR .
- Refer to INSTALLING THE INTAKE FILTER HOUSING (TENSION STRUT REMOVED ON SHOCK TOWER) .
- Refer to INSTALLING THE TENSION STRUT ON THE RIGHT SHOCK TOWER .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to CONNECTING ALL BATTERY GROUND LEADS .
- Refer to CHECKING/TOPPING UP THE OIL LEVEL IN THE AUTOMATIC TRANSMISSION .
- Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
- Refer to INSTALLING THE STIFFENING PLATE .
- Refer to INSTALLING FRONT UNDERBODY PROTECTION .