Installing the engine wiring harness for sensor system 1
Engine wiring harness for sensor system 1
NOTE:
RISK OF DAMAGE
Improper routing of cables and wiring harnesses.
Trapped, crushed or damaged cables may cause short circuits and malfunctions.
Improper routing of cables and wiring harnesses.
Trapped, crushed or damaged cables may cause short circuits and malfunctions.
- Route all cables without abrasions, do not trap and crush.
- Feed in and install the engine wiring harness (1)
for the sensor system 1.
- Connect connectors (3)
and lock.
The connector (3) must engage audibly.
- Connect connectors (2)
and lock.
The connectors (2) must engage audibly.
- Connect connectors (1)
and lock.
The connectors (1) must engage audibly.
- Secure the clamps (arrows).
- Secure clamps (1) .
- Secure clamps (2)
.
- Guide in and install the support (2) for the intake plenum.
- Tighten down screws (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Support to cylinder head | ||
| M6X16 | tightening torque | 8 Nm |
- Connect connectors (1)
and (2)
and lock.
The connectors (1) and (2) must engage audibly.
- Guide in the wiring harness section (2) and install.
- Make sure that the lock (arrow) snaps in correctly.
- Tighten down screws (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Cable bracket on rear cylinder head/transmission | ||
| M6 x 20 | Tightening torque | 10 Nm |
- Feed in and install the engine wiring harness (2) for the sensor system 1.
- Tighten down screws (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Cable bracket on rear cylinder head/transmission | ||
| M6 x 20 | Tightening torque | 10 Nm |
- Feed in and install the engine wiring harness (2) for the sensor system 1.
- Connect connectors (1)
and lock.
The connectors (1) must engage audibly.
- Secure the clamps (arrows).
- Feed in and install the engine wiring harness (2) for the sensor system 1.
- Connect connectors (1)
and lock.
The connectors (1) must engage audibly.
- Secure the clamps (arrows).
- Position the acoustic cover (2) .
- Secure expanding rivet (1)
.
- Fasten expanding rivet (1)
.
- Fasten expanding rivet (1)
.
- Insert and position the positive battery cable (2) .
- Secure clamps (1)
.
- Secure fir tree clip (1)
.
- Connect connectors (2)
and lock.
The connector (2) must engage audibly.
- Tighten the nut (1) hand-tight.
CAUTION:
Improper routing of the positive battery cable.
Risk of short circuits!
Risk of short circuits!
- Route the positive battery cable without abrasions and do not trap.
- Attach the positive battery cable (1) correctly to antitwist lock (2) .
- Tighten nut (3) .
TIGHTENING TORQUE SPECIFICATIONS
| Battery positive lead to starter | ||
| M8 | Tightening torque | 13.5 Nm |
Follow-up work
- Refer to RAISING THE FRONT AXLE SUPPORT AND FASTENING IT .
- Refer to SECURING THE ANTI-ROLL BAR LINK ON THE LEFT AND RIGHT ON THE ANTI-ROLL BAR .
- Refer to FASTENING ELECTRIC COOLANT PUMP AND COOLANT HOSES TO THE FRONT AXLE SUPPORT .
- Refer to IF INSTALLED: CONNECTING THE VACUUM LINE OF THE ENGINE MOUNTS .
- Refer to ATTACHING THE LINE CONNECTION OF THE RIDE HEIGHT SENSOR .
- Refer to SECURING THE EPS WIRING HARNESS TO THE ELECTROMECHANICAL STEERING GEAR .
- Refer to SECURING THE STEERING SHAFT AT THE BOTTOM ON THE STEERING GEAR .
- Refer to TAKING ENGINE OUT OF INSTALLATION ORIENTATION .
- Refer to INSTALLING THE INTAKE PLENUM .
- Refer to INSTALLING FUEL DELIVERY LINE .
- Refer to INSTALLING ALL IGNITION COILS .
- Refer to INSTALLING THE TANK VENT VALVE .
- Refer to INSTALLING THE CONTROL UNIT HOLDER .
- Refer to INSTALLING THE INTEGRATED POWER SUPPLY MODULE (PDM) .
- Refer to INSTALLING THE DME CONTROL UNIT .
- Refer to INSTALLING RESONATOR .
- Refer to INSTALLING INTAKE FILTER HOUSING .
- Refer to INSTALLING THE RIGHT FRONT-END STRUT .
- Refer to INSTALLING MOUNT OF HOOD SEAL ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE COVER IN THE ENGINE COMPARTMENT AT TOP LEFT AND RIGHT .
- Refer to INSTALLING ACOUSTIC COVER AT REAR .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to INSTALLING THE SECOND END PANEL UNDERNEATH .
- Refer to INSTALLING THE COWL UPPER PART .
- Refer to INSTALLING WINDSHIELD PANEL COVER .
- Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
- Refer to INSTALLING THE REAR HOOD SEAL .
- Refer to ACTIVATING ELECTRICAL SYSTEM .
- Refer to ACTIVATING THE 48 V ELECTRICAL SYSTEM .
- Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- Refer to FILLING AND VENTING THE LOW-TEMPERATURE COOLANT CIRCUIT .
- Refer to TAKING HOOD OUT OF THE SERVICE POSITION .
- Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
- Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
- Refer to INSTALLING FRONT UNDERBODY PROTECTION .
- Refer to INSTALLING THE COVER PANELS ON THE FRONT AXLE ON THE RIGHT AND LEFT .
- Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .