Install the wiring harness section of the transmission wiring harness
Wiring harness section of transmission wiring harness
NOTE:
RISK OF DAMAGE
Improper routing of cables and wiring harnesses.
Trapped, crushed or damaged cables may cause short circuits and malfunctions.
Improper routing of cables and wiring harnesses.
Trapped, crushed or damaged cables may cause short circuits and malfunctions.
- Route all cables without abrasions, do not trap and crush.
- Insert and install the wiring harness (1)
for the transmission module.
- Feed in and install the wiring harness section (3) of the transmission wiring harness.
- Connect connectors (1)
and lock.
The connector (1) must engage audibly.
- Tighten down screw (2) .
TIGHTENING TORQUE SPECIFICATIONS
| Grounding cable/wiring harness section to transmission | ||
| BM6 | Tightening torque | 8 Nm |
- Feed in and install the wiring harness section (2) of the transmission wiring harness.
- Secure the clamps (arrows).
- Connect connectors (1)
and lock.
The connector (1) must engage audibly.
- Thread in the wiring harness section (2) of the supply module and install.
- Secure clamp (arrow).
- Connect connectors (1)
and lock.
The connector (1) must engage audibly.
- Insert and install the holder (2) .
- Replace screws (1)
.
Parts: Screws
- Tighten the screws (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Holder on the transmission | ||
| Torx screw BM8 Replace screws. |
Tightening torque | 19 Nm |
Fastening the transmission
- Move the transmission (3) to the installation position.
- Replace screws (2)
.
Parts: Screws
- Tighten down screws (2) .
TIGHTENING TORQUE SPECIFICATIONS
| Transmission cross member to body | ||
| M8 | Tightening torque | 19 Nm |
- Secure the cable with the clamp (1) .
- Loosening the luggage strap (1) .
- Remove special tools 2 219 012 and 0 495 498 (23 4 050) .
- Secure clamps (2) .
- Connect connectors (1)
and lock.
The connector (1) must engage audibly.
- Feed in and install the wiring harness section (1) of the transmission wiring harness.
- Secure the clamps (arrows).
- Feed in and install the wiring harness section (2) of the transmission wiring harness.
- Secure clamp (arrow).
- Connect connectors (1)
and lock.
The connector (1) must engage audibly.
- Secure the clamp (2) .
- Connect connectors (1)
and lock.
The connector (1) must engage audibly.
- Feed in and install the wiring harness section (3) of the transmission wiring harness.
- Make sure that the lock (2) engages correctly.
- Tighten down screws (1) .
TIGHTENING TORQUE SPECIFICATIONS
| Cable bracket on rear cylinder head/transmission | ||
| M6 x 20 | Tightening torque | 10 Nm |
- Secure the clamps (arrows).
Follow-up work
- Refer to IF INSTALLED: SCREWING DOWN TRANSMISSION SUPPORT BRACKET .
- Refer to FASTENING THE PROP SHAFT (PARTIALLY REMOVED) .
- Refer to INSTALLING THE HEAT SHIELDS .
- Refer to INSTALLING THE RETAINING PLATES .
- Refer to SECURING UNDERBODY PANELING ON LEFT AND RIGHT SIDE .
- Refer to INSTALLING EXHAUST SYSTEM .
- Refer to INSTALLING THE CONNECTING SUPPORTS ON THE TUNNEL .
- Refer to INSTALLING TANK COVER ON LEFT AND RIGHT .
- Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
- Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
- Refer to INSTALLING THE CONTROL UNIT HOLDER .
- Refer to INSTALLING THE INTEGRATED POWER SUPPLY MODULE (PDM) .
- Refer to INSTALLING THE DME CONTROL UNIT .
- Refer to INSTALLING ACOUSTIC COVER AT REAR .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to INSTALLING THE COWL UPPER PART .
- Refer to INSTALLING WINDSHIELD PANEL COVER .
- Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
- Refer to INSTALLING THE REAR HOOD SEAL .
- Refer to ACTIVATING ELECTRICAL SYSTEM .