Refitting/installing sump

NOTE: RISK OF DAMAGE
Contaminant or foreign body.
Contamination can result in malfunctions, loss of function or leaks.

Adhere to the utmost cleanliness.
Protect components from contamination e.g. by covering.
Close off line connections with seal plugs.

NOTE: RISK OF DAMAGE
Damage to the surface.
The use of metal-cutting tools (e.g., emery cloths) for cleaning surfaces can damage them and lead to leaks and/or engine damage.

Do not use any metal-cutting tools.

NOTE: TECHNICAL INFORMATION
The sealing surfaces must be free of oil, grease and cleaning agents.

Remove rough seal remains on the sealing surface (1) of the crankcase with the special tool 0 495 102 (11 4 470).
Clean the sealing surface (1) with brake cleaner.

Courtesy of BMW OF NORTH AMERICA, INC.

CONSUMABLE SPECIFICATION

Brake cleaner 2.0	500 ml, Spray can	83192365214
Brake cleaner 2.0	20, Canister	83192365215

NOTE: TECHNICAL INFORMATION
The sealing surfaces must be free of oil, grease and cleaning agents.

Remove fine seal remains on the sealing surface (1) of the oil pan with the special tool 0 495 102 (11 4 470).
Clean the sealing surface (1) with brake cleaner.

CONSUMABLE SPECIFICATION

Consumable
Brake cleaner 2.0	500 ml, Spray can	83192365214
	20, Canister	83192365215

Courtesy of BMW OF NORTH AMERICA, INC.

Have the special tool 2 469 803 ready.

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
For additional information see: 11 00... OVERVIEW OF CONSUMABLES in applicable BMW parts catalogue

Position the sealing compound (1) as shown on the special tool 2 469 803.

Parts: Sealing compound

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
The processing time of the liquid sealing compound can be at a maximum of 10 min.
Commissioning of the assembly is not possible until 25 minutes after the processing time.
Non-observance can lead to leaks in the assembly.

Courtesy of BMW OF NORTH AMERICA, INC.

Apply a sealing bead (1) with the sealing compound in the marked area along the inner edge.
Completely encircle the oil return orifice (arrow) with the sealing compound.

The sealant must not enter the oil return orifice.

SEALING COMPOUND SPECIFICATION

Loctite 5970 liquid sealing compound Processing time <10 minutes at room temperature

50 ml, Cartridge

83190404517

TECHNICAL DATA SPECIFICATION

Height of the sealing bead
	2.0 mm... 2.5 mm

NOTE: TECHNICAL INFORMATION
The special tool 11 8 780 is only required when the transmission is removed.

Position the special tool 0 496 120 (11 8 780) with the transmission bolts (1) in such a way that the oil pan aligns exactly with the timing case cover.
Replace the centering sleeves where required.

Courtesy of BMW OF NORTH AMERICA, INC.
Install oil sump (1) to top front.
Tighten all bolts of the oil pan hand-tight, do not tighten completely.

Courtesy of BMW OF NORTH AMERICA, INC.
Tighten down screws (2) .

TIGHTENING TORQUE SPECIFICATION

Transmission to oil pan (manual transmission and automatic transmission)
M8 x 50	Tightening torque	19 Nm

Attach cable in the marked area.
Connect connector (1) .

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down screws (2) .

TIGHTENING TORQUE SPECIFICATION

Oil sump to crankcase
M8 x 110	Tightening torque	24 Nm

Tighten down screws (1) .

Courtesy of BMW OF NORTH AMERICA, INC.

TIGHTENING TORQUE SPECIFICATION

Oil sump to crankcase
M8 x 30	Tightening torque	24 Nm

Tighten all screws (marks).

TIGHTENING TORQUE SPECIFICATION

Oil sump to crankcase
M8 x 30	Tightening torque	24 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten all screws (marks).

TIGHTENING TORQUE SPECIFICATION

Oil sump to crankcase
M8 x 30	Tightening torque	24 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten all screws (marks).

TIGHTENING TORQUE SPECIFICATION

Oil sump to crankcase
M8 x 30	Tightening torque	24 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to INSTALLING STARTER MOTOR .
Refer to INSTALLING THE ACOUSTIC COVER FOR THE OIL SUMP .
Refer to INSTALLING THE FRONT AXLE SUPPORT .
Refer to PARTIALLY INSTALLING THE AIR DUCT FOR THE BRAKE ON THE LEFT AND RIGHT .
Refer to ATTACHING THE LEFT AND RIGHT TENSIONING STRUTS ON THE SWIVEL BEARING .
Refer to ATTACHING THE LEFT AND RIGHT WISHBONE ON THE SWIVEL BEARING .
Refer to SECURING THE TIE ROD ON THE LEFT AND RIGHT OF THE SWIVEL BEARING .
Refer to ATTACHING THE ANTI-ROLL BAR LINK ON THE ANTI-ROLL BAR AT LEFT AND RIGHT .
Refer to ATTACHING THE LINE CONNECTION TO THE RIDE HEIGHT SENSOR .
Refer to SECURING THE WIRING HARNESS FOR THE EPS ON THE FRONT AXLE SUPPORT .
Refer to SECURING THE STEERING SHAFT AT THE BOTTOM ON THE STEERING GEAR .
Refer to REMOVING THE ENGINE FROM THE INSTALLATION POSITION .
Refer to INSTALLING THE REAR SECTION OF THE FRONT WHEEL ARCH COVER .
Refer to INSTALLING THE FRONT SECTION OF THE FRONT WHEEL ARCH COVER .
Refer to INSTALLING THE LOWER WHEEL ARCH COVER ON THE LEFT AND RIGHT .
Refer to INSTALLING THE COVER OF THE STEERING ASSEMBLY ON THE LEFT AND RIGHT .
Refer to INSTALLING THE CENTER UNDERBODY PROTECTION .
Refer to INSTALLING UNDERBODY PROTECTION AT REAR .
Refer to IF INSTALLED: INSTALLING UNDERBODY PROTECTION FOR THE STEERING .
Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR .
Refer to INSTALLING FRONT UNDERBODY PROTECTION .
Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
Refer to FASTENING THE WIRING HARNESS SECTION TO THE LEFT SHOCK TOWER .
Refer to FASTENING THE WIRING HARNESS SECTION TO THE RIGHT SHOCK TOWER .
Refer to INSTALLING THE SIDE PANEL SEAL .
Refer to INSTALLING THE LATERAL HOOD SEALS .
Refer to INSTALLING INTAKE FILTER HOUSING .
Refer to INSTALLING ACOUSTIC COVER .
Refer to FILLING ENGINE OIL .
Refer to OPENING THE OIL FILLER CAP .
Refer to RECONNECTING ALL BATTERY GROUND LEADS .
Refer to ACTIVATING THE 48 V ELECTRICAL SYSTEM .
Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
Refer to CHECKING ENGINE OIL LEVEL .
Refer to TAKING HOOD OUT OF THE SERVICE POSITION .