Raise the front axle support and fasten it

WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2025 BMW X4, 2024 BMW X4, 2023 BMW X4, 2022 BMW X4, and 2021 BMW X4. However, it is still accessible from the selected car via links, so may be relevant.

Raise front axle support

Do not damage the steering gear

NOTE: RISK OF DAMAGE
Failure to comply with the specification.
Component damage.

All specifications must be observed and complied with.

When lifting the front subframe, ensure sufficient distance between the steering gear (1) and the output shaft (2).

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Perform the steps on the right and left side.

Position the front axle support (1) to the right and left on the adapter for the front axle support (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Carefully raise the front axle support with the universal jack 0 490 133 (00 2 030) and position on the body.

Courtesy of BMW OF NORTH AMERICA, INC.

Fasten front axle support

Securing the front axle support adapter on the front axle support on the right and left

NOTE: Perform the steps on the right and left side.

Position the adapter (1) for the front subframe (2) on the front subframe (2).
Tighten down screws (3).

TIGHTENING TORQUES SPECIFICATION

Adapter, front axle support to front axle support
M8x80	Tightening torque	19 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Attaching left and right crash levers

NOTE: The following step(s) must be performed if the specified component(s) is/are installed.

Replace nut (1).
Parts: Nut
Insert screw (2).
Tighten nut (1).

TIGHTENING TORQUES SPECIFICATION

Crash lever on front subframe
M12 Replace nut.	tightening torque	65 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Replace screws (1) to (3).
Parts: Screws
Tighten down screws (1).

TIGHTENING TORQUES SPECIFICATION

Front axle carrier to body, front
M12x115 Replace screws.	Joining torque	100 Nm
	Angle of rotation	90°

Fig 1: Front Axle Support Screws Tightening Sequence

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down screws (2).

TIGHTENING TORQUES SPECIFICATION

Front axle support to center of body
M12x90 Replace screws.	Joining torque	100 Nm
	Angle of rotation	90°

Tighten down screws (3).

TIGHTENING TORQUES SPECIFICATION

Front axle carrier to body, rear
M14 Replace screws.	Joining torque	100 Nm
	Angle of rotation	90°

If necessary, remove the special tool (tensioning strap) 0 496 080 (33 5 206).
Lower the universal jack 0 490 133 (00 2 030) and place to one side.

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to SECURING THE ANTI-ROLL BAR LINK ON THE LEFT AND RIGHT ON THE ANTI-ROLL BAR .
Refer to FASTENING ELECTRIC COOLANT PUMP AND COOLANT HOSES TO THE FRONT AXLE SUPPORT .
Refer to IF INSTALLED: CONNECTING THE VACUUM LINE OF THE ENGINE MOUNTS .
Refer to ATTACHING THE LINE CONNECTION OF THE RIDE HEIGHT SENSOR .
Refer to SECURING THE EPS WIRING HARNESS TO THE ELECTROMECHANICAL STEERING GEAR .
Refer to SECURING THE STEERING SHAFT AT THE BOTTOM ON THE STEERING GEAR .
Refer to INSTALLING THE COVER PANELS ON THE FRONT AXLE ON THE RIGHT AND LEFT .
Refer to INSTALLING FRONT UNDERBODY PROTECTION .
Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
Refer to ACTIVATING ELECTRICAL SYSTEM .