Installing wiring harness for sensor system of cylinder bank 2

Wiring harness for the sensor system of cylinder bank 2 

Courtesy of BMW OF NORTH AMERICA, INC.

• Guide in and position wiring harness for sensor system of cylinder bank 2.
• Connect and lock the plug connection for the knock sensors (2)  .
• The wiring harness mountings must be released (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect and lock the connector of the exhaust VANOS solenoid actuator (1)  .
• Connect and lock the intake VANOS solenoid actuator (4)  .
• Secure the wiring harness mounting (2)  .
• Tighten down screw (3)  .

Courtesy of BMW OF NORTH AMERICA, INC.

• Secure the wiring harness for the sensor system of cylinder bank 2 to the holders in areas (2)  .
• Connect connectors (1)  and lock.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect connectors (1)  and lock.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect the wiring harness bracket at the area (1)  and lock.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure the wiring harness for the sensor system of cylinder bank 2 in the holders in areas (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect connectors (1)  and lock.
• Secure the wiring harness for the sensor system of cylinder bank 2 in the holder (2)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect connectors (1)  and lock.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure the wiring harness for the sensor system of cylinder bank 2 in the holders in areas (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect connectors (1)  and lock.
• Secure the wiring harness for the sensor system of cylinder bank 2 in the holders in area of arrows.
• Position the grounding point (3)  .
• Tighten down screw (2)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Connect connectors (1)  and lock.
• Tighten down screw (2)  .
• Secure the wiring harness for the sensor system of cylinder bank 2 in the holder in area (3)  .
• Tighten down screw (2)  .
• Position the grounding point (5)  .
• Position the grounding point (6)  .
• Tighten the screws (4)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure the wiring harness mounting in area (1)  .
• Connect connectors (2)  and lock.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Ensure that the connector of the high pressure pump is (1) not  interchanged with the connector of the intake air temperature sensor.
• Make marks if there are no colored marks (3)  on the plug connections of the high pressure pump.

  If necessary, identify the connectors by means of the cable colors in area (2)  on the wiring diagram.

  Courtesy of BMW OF NORTH AMERICA, INC.

• Ensure that the connector of the intake air temperature sensor is (1) not  interchanged with the connector of the high pressure pump.
• If necessary, identify the connectors using the wiring diagram and the cable colors in the area (2)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure the wiring harness for the sensor system of cylinder bank 2 in the holder in area (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Secure the wiring harness for the sensor system of cylinder bank 2 in the holders in areas (1)  .

  Courtesy of BMW OF NORTH AMERICA, INC.

• Fix wiring harness mountings (1)  .
• Connect connectors (2)  and lock.

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work 

• Refer to INSTALLING THE LEFT INTAKE PLENUM .
• Refer to INSTALLING THE LEFT ENGINE SUPPORT BRACKET .
• Refer to INSTALLING FRONT AXLE COMPLETELY .
• Refer to TIGHTENING THE BOLTS ON THE FRONT AXLE SUPPORT .
• Refer to ATTACHING COOLANT HOSES TO FRONT SUBFRAME .
• Refer to ATTACHING THE THERMOSTAT OR TRANSMISSION OIL COOLER LINE ON THE FRONT SUBFRAME .
• Refer to INSTALLING THE UNIVERSAL JOINT .
• Refer to INSTALLING THE OUTPUT SHAFTS .
• Refer to SECURING CABLES ON VERTICAL ACCELERATION SENSOR ON RIGHT AND LEFT .
• Refer to ATTACHING THE CABLE OF THE WHEEL RPM SENSOR ON THE LEFT AND RIGHT .
• Refer to INSTALLING THE BRAKE CALIPER AT THE FRONT LEFT AND RIGHT .
• Refer to SECURING THE RIGHT AND LEFT OUTPUT SHAFTS ON THE WHEEL BEARING .
• Refer to CHECK/ADD FRONT AXLE TRANSMISSION OIL .
• Refer to IF INSTALLED: CONNECTING THE CONNECTOR OF THE ACTIVE STABILIZER .
• Refer to INSTALLING THE COVER OF THE STEERING ASSEMBLY ON THE LEFT AND RIGHT .
• Refer to IF INSTALLED: INSTALLING THE SILENCER OF THE STATIONARY HEATING .
• Refer to INSTALLING THE WHEEL ARCH COVER ON THE FRONT LEFT AND BOTTOM RIGHT .
• Refer to INSTALLING LEFT AND RIGHT BRAKE VENTILATION DUCT .
• Refer to SECURING THE WIRING HARNESS FOR THE EPS ON THE FRONT AXLE SUPPORT .
• Refer to INSTALLING THE REINFORCEMENT STRUT ON THE RIGHT ENGINE MOUNT .
• Refer to INSTALLING THE STIFFENING PLATE .
• Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
• Refer to INSTALLING THE FRONT UNDERBODY PROTECTION OR FRONT THRUST FIELD .
• Refer to REMOVING THE SECURING TOOL OF THE ENGINE IN INSTALLATION POSITION .
• Refer to INSTALLING THE REAR SECTION OF THE FRONT WHEEL ARCH COVER ON THE LEFT AND RIGHT .
• Refer to SECURING THE AIR SUSPENSIONS STRUTS IN THE FRONT .
• Refer to INSTALLING THE FRONT LEFT AND RIGHT WHEELS .
• Refer to INSTALLING THE LATERAL HOOD SEALS .
• Refer to INSTALLING THE MOUNT OF THE HOOD SEAL .
• Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT CENTER .
• Refer to TAKING HOOD OUT OF THE SERVICE POSITION .
• Refer to CONNECTING ALL BATTERY GROUND LEADS .
• Refer to ACTIVATING THE 48 V ELECTRICAL SYSTEM .
• Refer to CHECKING THE STRAIGHT-AHEAD DRIVING POSITION OF THE STEERING WHEEL .
• Refer to CHECKING THE AIRBAG FOR FUNCTION .