Installing the intake adjuster

Intake adjuster

Courtesy of BMW OF NORTH AMERICA, INC.

Overview

Overview graphic of the intake adjuster

8 617 692

8 684 920

NOTE: TECHNICAL INFORMATION
After replacing one or more VANOS central valves or VANOS adjusters:
When removing, make note of the identification/part number of the VANOS central valve or VANOS adjuster and consider writing it down.
It must be replaced with a VANOS adjuster or VANOS central valve with the same part number. A mixed installation is not allowed.
Read out the vehicle l-level and proceed accordingly.
For further information, see the applicable BMW parts catalogue.

Lay out the intake adjuster marked with IN (arrow).

Courtesy of BMW OF NORTH AMERICA, INC.
Feed in intake adjuster (1) in the timing chain (2) and position on the intake camshaft (3) .

Courtesy of BMW OF NORTH AMERICA, INC.
Abut VANOS central valve (1) of intake side.

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to INSTALLING VANOS CENTRAL VALVE OF THE INTAKE SIDE .
Refer to PRELOAD TIMING CHAIN .
Refer to TIGHTENING THE VANOS CENTRAL VALVE .
Refer to DISASSEMBLING ALL SPECIAL TOOLS .
Refer to CHECKING CAMSHAFT TIMING .
Refer to INSTALLING THE THERMOSTAT ON THE TRANSMISSION OIL LINES .
Refer to SECURING THE OIL SUMP ACOUSTIC COVER .
Refer to INSTALLING CYLINDER HEAD COVER .
Refer to INSTALLING BOTH ACTUATORS .
Refer to PREPARING THE INJECTORS FOR INSTALLATION .
Refer to INSTALLING INJECTORS .
Refer to INSTALLING HIGH PRESSURE PUMP .
Refer to INSTALLING FUEL DELIVERY LINE .
Refer to INSTALLING THE HIGH-PRESSURE LINE BETWEEN THE HIGH-PRESSURE PUMP AND THE HIGH-PRESSURE RAIL .
Refer to INSTALLING ALL SPARK PLUGS .
Refer to INSTALLING THE IGNITION COILS .
Refer to INSTALLING THE CYLINDER HEAD COVER ACOUSTIC COVER .
Refer to INSTALLING FRONT ENGINE ENCAPSULATION .
Refer to INSTALLING AUXILIARY COOLANT PUMP FOR THE TURBOCHARGER .
Refer to INSTALLING THE ACOUSTIC COVER FOR THE ENGINE AT THE FRONT .
Refer to CONNECTING THE COOLANT LINE OF HIGH-TEMPERATURE COOLANT CIRCUIT .
Refer to INSTALLING CHARGE AIR LINE .
Refer to INSTALLING CLEAN AIR PIPE .
Refer to INSTALLING RESONATOR .
Refer to INSTALLING INTAKE SILENCER HOUSING .
Refer to INSTALLING CENTER FIREWALL LOWERING PART .
Refer to INSTALLING ACOUSTIC COVER AT REAR .
Refer to LOOSENING HIGH-VOLTAGE CABLES ON THE ELECTRICAL MACHINE ELECTRONICS .
Refer to INSTALLING RIGHT SEALING FRAME .
Refer to INSTALLING LEFT SEALING FRAME .
Refer to INSTALLING THE CENTER COWL UPPER PART .
Refer to INSTALLING BOTH TENSION STRUTS FROM SHOCK TOWER .
Refer to INSTALLING WINDSHIELD PANEL COVER .
Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .
Refer to FILLING THE HIGH-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
Refer to CONNECTING ALL BATTERY GROUND LEADS .
Refer to VENTING THE HIGH-TEMPERATURE COOLANT SYSTEM .
Refer to CONNECTING THE DIAGNOSTIC SYSTEM FOR POSSIBLE INTEGRATION LEVEL ENCODING AND PROGRAMMING .
Refer to CHECKING/TOPPING UP THE OIL LEVEL IN THE AUTOMATIC TRANSMISSION .
Refer to CHECKING ENGINE OIL LEVEL .
Refer to INSTALLING ACOUSTIC COVER .
Refer to INSTALLING THE REAR THRUST FIELD .
Refer to INSTALLING FRONT STIFFENING PLATE .
Refer to TAKING HOOD OUT OF THE SERVICE POSITION .