24 34 568 Replacing Mechatronics (GA8P70H) N55_Hybrid

WARNING: This page does not describe the selected car, but rather 50 other vehicles, including the 2016 BMW M5, 2016 BMW ActiveHybrid 5, 2016 BMW 550i xDrive, 2016 BMW 550i, and 2016 BMW 535i xDrive. However, it is still accessible from the selected car via links, so may be relevant.

Special tools required:

IMPORTANT:

Do not let skin come in contact with transmission oil and do not inhale fuel vapors.
Wear protective gloves.
Ensure adequate ventilation.

NOTE: After completing repair work:

Load specific data status with the BMW diagnosis system.

IMPORTANT: After completion of repair work, CHECK TRANSMISSION OIL LEVEL .
Use only approved transmission oil .
Failure to comply with this requirement will result in serious damage to the automatic transmission!

IMPORTANT: Read and comply with notes on PROTECTION AGAINST DAMAGE FROM ELECTROSTATIC DISCHARGE (ESD PROTECTION) .

Necessary preliminary tasks:

Remove rear UNDERBODY PROTECTION .

Remove panels (2).

Fig 1: Ground Strap And Retaining Plates

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Mechatronics can be destroyed by static discharges. Therefore the contacts inside the connector must not be touched. Insert special tool immediately after operation.

Unscrew connector (1) and disconnect.

Fig 2: Disconnecting Automatic Transmission Connector

Courtesy of BMW OF NORTH AMERICA, INC.

Insert special tool 24 2 390 in sealing cup (1).

Fig 3: Inserting Special Tool (24 2 390) In Sealing Sleeve

Courtesy of BMW OF NORTH AMERICA, INC.

Remove TRANSMISSION OIL SUMP .

Remove OIL PUMP (IEP) .

Release screw (1) and unlock sealing cup with slide (2).

Tightening torque: 24 30 4AZ .

Fig 4: Sealing Cup And Screw

Courtesy of BMW OF NORTH AMERICA, INC.

Note position of sealing cup.

Pull out sealing cup (1).

Installation note:

Fit sealing cup in position (lug on inside). Turn until lug engages in groove of transmission. Slide in sealing cup.

Lug on sealing cup must not be damaged!

Fig 5: Pulling Sealing Cup

Courtesy of BMW OF NORTH AMERICA, INC.

Release all screws (1 and 2).

1 = M6 x 59 mm.
2 = M6 x 20 mm.

Remove mechatronics.

Installation note:

Replace O-rings for oil ducts on the mechatronics unit and wet with automatic transmission fluid.

Fig 6: Mechatronics Screw

Courtesy of BMW OF NORTH AMERICA, INC.

Installation note:

Check gasket (1) for damage.

Replace the gasket (1) if necessary.

Coat new gasket with automatic transmission fluid and install.

Fig 7: Automatic Transmission Fluid Gasket

Courtesy of BMW OF NORTH AMERICA, INC.

Screw in guide pins 24 1 430 at screw position 4 and 9.

Fig 8: Guide Pins (24 1 430)

Courtesy of BMW OF NORTH AMERICA, INC.

Fit mechatronics unit.

Fit shift claw (2) in gearshift shaft (3) by pressing release lever (1).

Fig 9: Fitting Shift Claw In Gearshift Shaft By Pressing Release Lever

Courtesy of BMW OF NORTH AMERICA, INC.

Screw down wing nuts as far as they will go on to the mechatronics unit.

Fig 10: Special Tool (24 1 430)

Courtesy of BMW OF NORTH AMERICA, INC.

Installation note:

Insert screws until screw heads make contact.

Remove guide pins and fit remaining screws.

IMPORTANT: Tighten down screws in order 1...18.
Failure to comply with this requirement will result in serious damage to the automatic transmission!
Tightening torque: 24 30 4AZ .

Fig 11: Automatic Transmission Valve Body (Mechatronics) Screws Tightening/Loosening Sequence

Courtesy of BMW OF NORTH AMERICA, INC.