61 11 200 Installing repair cable for reversing camera (TRSVC)

Read and comply with notes on HANDLING WIRING HARNESSES AND WIRING .

Necessary preliminary tasks:

Remove and install TAILGATE TRIM .
Remove and install TRIM PANEL FOR REAR ROOF PILLAR (D-PILLAR) on right.
Remove and install RIGHT LUGGAGE COMPARTMENT WHEEL ARCH TRIM .
Remove and install REAR DOOR SILL COVER STRIP on right.
Remove and install SIDE TRIM PANEL, FOOTWELL, ON A-PILLAR, RIGHT .
Remove and install TAILGATE TRIM .
Remove and install SIDE CARPET ON STORAGE COMPARTMENT (CENTRE CONSOLE) .

Release screws (1) on driver's and passenger sides and remove air duct (2).

Fig 1: Identifying Air Duct And Screws

Courtesy of BMW OF NORTH AMERICA, INC.

Unlock the lock (1) in direction of arrow with suitable tool.

IMPORTANT: Risk of damage!

Unlock the lock (3) carefully with a suitable tool. Pull connector housing (4) of line (2) in direction of arrow.

Installation note:

Pay attention to encoding (5)!

Fig 2: Pulling Connector Housing Of Line

Courtesy of BMW OF NORTH AMERICA, INC.

Tape off ground (1) on repair cable to prevent damage during routing.

Fig 3: Identifying Repair Cable Ground

Courtesy of BMW OF NORTH AMERICA, INC.

Pull off connector (1) and tie back onto wiring harness (2).

Connect repair cable to camera and route and secure along wiring harness (2).

Fig 4: Routing Wiring Harness

Courtesy of BMW OF NORTH AMERICA, INC.

Unclip wiring harness (1) at the position marked in the image and release from the tailgate.

Route and secure repair cable along wiring harness (1).

Attach wiring harness (1) to tailgate.

Fig 5: Routing Repair Cable Wiring Harness

Courtesy of BMW OF NORTH AMERICA, INC.

Unclip rubber grommet (1) from vehicle body and tailgate.

Unclip cable duct (2) from tailgate.

Route repair cable with feed-in aid through cable duct (2) and rubber grommet (1).

Open abrasion protection (3) and pass repair cable through to passenger compartment.

Close abrasion protection (3).

Attach rubber grommet (1) and cable duct (2).

Fig 6: Routing Repair Cable With Feed-In Aid Through Cable Duct And Rubber Grommet

Courtesy of BMW OF NORTH AMERICA, INC.

Route and secure repair cable along wiring harness (1).

Release ground point (2) and attach repair cable.

Fig 7: Routing Repair Cable Wiring Harness

Courtesy of BMW OF NORTH AMERICA, INC.

Route and secure repair cable (2) along wiring harness (1).

Fig 8: Routing Repair Cable Along Wiring Harness

Courtesy of BMW OF NORTH AMERICA, INC.

Lift carpet in area of rear entry strip.

Remove feeder (2).

Open cable channel (1) and route and secure repair cable on wiring harness.

Fig 9: Identifying Feeder And Cable Channel

Courtesy of BMW OF NORTH AMERICA, INC.

Lift carpet in area of front entry strip.

Open cable channel (1 and 2) and route and secure repair cable on wiring harness.

Fig 10: Lifting Carpet In Area Of Front Entry Strip

Courtesy of BMW OF NORTH AMERICA, INC.

Route and secure repair cable (1) on wiring harness (2) in footwell.

Fig 11: Routing Repair Cable On Wiring Harness In Footwell

Courtesy of BMW OF NORTH AMERICA, INC.

Feed through repair cable (1) under heating and air-conditioning unit (2) from passenger footwell into driver's footwell.

Fig 12: Identifying Repair Cable, Under Heating And Air-Conditioning Unit

Courtesy of BMW OF NORTH AMERICA, INC.

Lay repair cable in direction of arrow under heating and air-conditioning unit (1), foam material (2) and carpet (3).

Fig 13: Laying Repair Cable In Under Heating Or Air-Conditioning Unit, Foam Material And Carpet

Courtesy of BMW OF NORTH AMERICA, INC.

Route repair cable in direction of arrow and secure.

Fig 14: Routing Repair Cable

Courtesy of BMW OF NORTH AMERICA, INC.

Plug 1	Bumper camera, right
Plug 2	Exterior mirror camera, right
Plug 3	Reversing camera
Plug 4	Bumper camera, left
Plug 5	Exterior mirror camera, left

Pull off connector (3) on TRSVC control unit.

Fig 15: Identifying Plugs And Connector

Courtesy of BMW OF NORTH AMERICA, INC.

Tie back cable that has been pulled off to the wiring harness.

Attach repair cable at free slot.

NOTE: Lay any repair cable overlength under carpet and secure.
Once the camera has been successfully checked, cut off old cable connector.