Output Flange Seal, Replacing

WARNING: This page is about a different variant/trim than selected.

Special tools and workshop equipment required

Press Plate: VW401
Press Plate: VW402
Press Piece - Rod: VW407
Press Piece - Multiple Use: VW412
Press Piece - Multiple Use: VW454
Press Piece - Multiple Use: VW455
Support Channels: VW457
Press Piece - Reverse Gear Syncro: 3296
Gearbox Support: T10108 with Counter Holder: T10108/1
Puller - Taper Roller Bearing: VAG1582
Puller - Taper Roller Bearing - Adapter 13: VAG1582/13
Torque Wrench 1601: VAG1601
Seal Installer - Crankshaft: VW204B
Dial Gauge Holder: VW387
Press Piece - Multiple Use: 40-105
Dial Indicator: VAS6080A
Socket AF 34mm: T50019
Sealing Grease. Refer to the Parts Information.
M10 x 30 bolt (quantity: 2)
M8 x 25 bolt (quantity: 1)
M12 x 10 nut (quantity: 4)

Procedure

A tapered roller bearing inner race is pressed onto the bevel box output flange.
This is removed later in the procedure.
Do not replace the tapered roller bearing for the bevel box output flange and the shims.

-- Remove the bevel box. Refer to BEVEL BOX, REMOVING .

-- Place the bevel box on the hole -arrow- marked with the number "4" in the : T10108 . Place the M12 x 10 nut -A- between the bevel box and the transmission holder to do so.

Fig 1: Identifying Bevel Box Set On Hole Designated With Number 4 In Gearbox Support T10108

Courtesy of AUDI OF AMERICA, LLC

-- Align the bevel box with the remaining three holes and secure it with the nuts -A- inserted between.

-- Drain the gear oil from the bevel box. Refer to GEAR OIL, DRAINING AND FILLING .

-- Turn the peenings -arrows- on the twelve point nut -A- back into the output flange depressions -B-.

Fig 2: Securing Twelve-Point Nut -A-

Courtesy of AUDI OF AMERICA, LLC

-- Lock the bevel box output flange using the : T10108/1 by installing the two M10 x 30 bolts -arrows-.

Fig 3: Identifying New Output Flange Hex Nut

Courtesy of AUDI OF AMERICA, LLC

A -

: T50019

-- Remove the output flange nut.

-- Pivot the bevel box so that the output flange faces upward.

-- Remove the bolts -arrows- for the pinion housing -A-.

Fig 4: Removing Bolts For Pinion Housing

Courtesy of AUDI OF AMERICA, LLC

-- Position a suitable flat-head screwdriver -B- into the three recesses -arrows- on the pinion housing -A- and carefully pry out the pinion housing together with the shaft bevel gear.

Fig 5: Insert Suitable Flathead Screwdriver

Courtesy of AUDI OF AMERICA, LLC

-- Place the output flange -A- evenly onto the : VW457 -arrows-.

Fig 6: Shaft Bevel Gear

Courtesy of AUDI OF AMERICA, LLC

-- Remove the shaft bevel gear from the output flange -A-.

Secure the shaft bevel gear and tapered bearing inner race from falling.

-- Remove the output flange -A- from the pinion housing.

Fig 7: Output Flange And Pinion Housing

Courtesy of AUDI OF AMERICA, LLC

The seal -arrow- is located on the output flange.

Fig 8: Identifying Output Flange Seal -Arrow-, Removal And Installation
Courtesy of AUDI OF AMERICA, LLC

The tapered bearing inner race must be removed from the output flange to remove the seal.

Fig 9: Identifying Tapered Roller Bearing Puller V. A. G 1582 And Adapter
Courtesy of AUDI OF AMERICA, LLC

CAUTION:

Risk of Damaging the Tapered Bearing Inner Race.

- Remove the tapered bearing inner race using the Puller - Taper Roller Bearing - Adapter 13: VAG1582/13 .

- Replace the bevel box if the tapered bearing inner race is damaged.

-- Place the : 40-105 on the output flange.

-- Remove the tapered bearing inner race from the output flange using the : VAG1582 .

-- Remove the output flange seal.

-- Insert the old tapered bearing inner race -1- into the pinion housing.

Fig 10: Identifying Inner Race/Tapered Roller Bearing -1- And Output Flange Sealing Ring -2-

Courtesy of AUDI OF AMERICA, LLC

-- Lightly lubricate the outer diameter of the new output flange seal -2-.

-- Install the seal so that it is flush.

Fig 11: Install New Seal

Courtesy of AUDI OF AMERICA, LLC

The larger diameter of the : VW204B points to the seal.

-- Fill the space between the sealing/dust lip halfway with sealing grease. Refer to the Parts Information for the correct sealing grease.

-- Install the tapered bearing inner race. Refer to OUTPUT FLANGE SEAL, REPLACING => Insert the old tapered bearing inner race -1- into the pinion housing. all the way onto the output flange.

Fig 12: Identifying Inner Race/Tapered Roller Bearing

Courtesy of AUDI OF AMERICA, LLC

The larger diameter of the : VW454 points to the output flange.
Install the tapered bearing inner race until it stops. Do not apply any greater pressure to the tapered roller bearing.

-- Place the shim -2-, the tapered bearing inner race -3- and the pinion housing -4- onto the shaft bevel gear -1-.

Fig 13: Inner Race/Tapered Roller Bearing And Pinion Housing

Courtesy of AUDI OF AMERICA, LLC

Re-install the old shim -2-. This ensures the bearing pre-load of the shaft bevel gear in the pinion housing.

-- Carefully press the pinion housing with the output flange all the way onto the shaft bevel gear.

Fig 14: Identifying Thrust Disc VW 412, Thrust Tube VW 454, Thrust Tube VW 455 And Thrust Plate VW 401

Courtesy of AUDI OF AMERICA, LLC

The shoulder -arrow- of the : VW455 points to the shaft bevel gear.
Turn the pinion housing during pressing procedure.

-- Align the old shim -3- to the pinion housing -2-.

Courtesy of AUDI OF AMERICA, LLC

The pinion housing -2- and shim -3- only fit in one position.

-- Coat the new O-ring -1- with gear oil and slide it onto the pinion housing -2-.

-- Insert the pinion housing -2- into the axle drive housing -4-.

The splines on the shaft and head bevel gear must come in contact.
Align the openings for the pinion housing bolts to the axle drive housing.

-- Tighten the bolts -1- in small steps, alternating from side to side. While doing so, turn the output flange -2- back and forth slightly in direction of -arrows-.

Fig 15: Tightening Bolts

Courtesy of AUDI OF AMERICA, LLC

-- Tighten the bolts -arrows- for the pinion housing -A- in a diagonal sequence.

Fig 16: Removing Bolts For Pinion Housing

Courtesy of AUDI OF AMERICA, LLC

-- Tighten the new output flange twelve-point nut.

Fig 17: Identifying New Output Flange Hex Nut

Courtesy of AUDI OF AMERICA, LLC

A -

: T50019

-- Secure the twelve-point nut -A-.

Fig 18: Securing Twelve-Point Nut -A-

Courtesy of AUDI OF AMERICA, LLC

-- With the nut offset by 120°, move it into the output flange depressions -B- -arrows-.

Radial Run-Out on Output Flange/Shaft Bevel Gear, Measuring

Fig 19: Measure the Radial Run-Out on the Output Flange/Shaft Bevel Gear

Courtesy of AUDI OF AMERICA, LLC

Check the radial run-out on the shaft bevel gear alignment pin after tightening the output flange nut.

-- Fasten the measuring tools to the bevel box using a M8 x 25 bolt -A-.

-- Position the : VAS6080A on the shaft bevel gear alignment pin -B- and set it to "0" with 1 mm pre-tension.

-- Turn the output flange one complete rotation -arrow-.

-- Read the measured value on the dial gauge.

Radial run-out: maximum 0.05 mm.

-- Install the bevel box. Refer to BEVEL BOX, INSTALLING .

-- Check the gear oil level. Refer to GEAR OIL, CHECKING LEVEL .

Tightening Specifications

Refer to OVERVIEW - BEVEL BOX COMPONENTS