Selector lever cable, removing and installing (vehicles with 2.0 ltr. TFSI engine)

WARNING: This page does not describe the selected car, but rather 10 other vehicles, including the 2009 Audi A4, 2008 Audi S4, 2008 Audi A4, 2007 Audi S4, and 2007 Audi A4. However, it is still accessible from the selected car via links, so may be relevant.

Removing

Shift selector lever to position "P".

Fig 1: Identifying Quick-Release Fasteners And Noise Insulation

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Open quick release fasteners - 2 - and - 3 - and remove rear sound insulation.

Fig 2: Pressing Ball Socket Of Selector Lever Cable From Selector Shaft Lever & Removing Bracket On Transmission

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Pry ball socket - 1 - of selector lever cable off selector shaft lever.
Remove support bracket from transmission - arrows -.

NOTE:

Shown in illustration with transmission support removed.

Fig 3: Removing/Installing Heat Shield For Driveshaft

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove heat shield - A - for driveshaft - arrows -.

Fig 4: Driveshaft Heat Shield Bolts

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove heat shield - 1 - for exhaust system below selector mechanism - arrows -.
Remove bolts at transmission/driveshaft flange.
Push driveshaft - 2 - together toward rear final drive. The constant velocity joints can be moved axially.

Fig 5: Drive Shaft Tied To Side, Onto Heat Shield

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Tie driveshaft up to side onto heat shield - arrow -.

Fig 6: Removing/Installing Lower Cover From/To Shift Mechanism

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove selector lever cable sleeve from selector mechanism cover (bottom) and slide back.
Remove cover on underside of selector mechanism - arrows -.

Fig 7: Identifying Retaining Clip, Securing Spring, Push Pin & Selector Lever Cable

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Remove retaining clip - 1 - for selector lever cable by pulling it off downward at selector mechanism.
Pull plastic securing spring - 2 - slightly forward and press pin - 3 - upward, but only as far as is necessary - arrow -.

NOTE:

Make sure that pin is not pressed out completely.

Pull selector lever cable - 4 - out of selector mechanism.

NOTE:

Do not bend or kink the selector lever cable.

Fig 8: Inserting End Of Selector Lever Cable Into Joint Of Selector Lever

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Installing

Installation is performed in reverse sequence. Note the following:

Install new retaining clip - 1 - for selector lever cable on selector mechanism.

Installation position: The angled end of the retaining clip faces to the inside of the selector mechanism.

Insert end of selector lever cable - 4 - in joint on selector lever.
Push pin - 3 - down - arrow -.
Check that plastic securing spring - 2 - has locked the pin.

Fig 9: Removing/Installing Lower Cover From/To Shift Mechanism

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Secure cover to underside of selector mechanism - arrows -.
Attach sleeve for selector lever cable to selector mechanism cover (bottom).
Shift selector lever from position "P" to "S".

Selector mechanism and selector lever cable must move freely. If necessary replace selector lever cable or service selector mechanism.

NOTE:

Do not bend or kink the selector lever cable.

Shift selector lever to position "P".

Fig 10: Pushing Lever/Selector Shaft On Transmission Fully Forward Into Position "S"

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Push selector shaft lever - 2 - on transmission toward rear as far as possible (in illustration: as far as possible to the right) until parking lock engages.

NOTE:

When the parking lock has engaged it should no longer be possible to rotate both front wheels in one direction.

Make sure that the selector lever cable - 1 - has not been bent or kinked and that it is not under tension.

Fig 11: Pressing Selector Lever Cable Onto Ball Head Of Selector Shaft Lever

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Carefully press selector lever cable - 1 - onto ball head of selector shaft lever - 3 -.

NOTE:

Make sure you do not bend the selector shaft lever when pressing on the ball socket, as this would make it impossible to obtain an accurate adjustment of the selector mechanism.

Fig 12: Identifying Cable Support Bracket To Transmission

Courtesy of VOLKSWAGEN UNITED STATES, INC.

Bolt on support bracket for selector lever cable - arrows -.
Adjust selector lever cable → Selector lever cable, checking and adjusting .
Bolt driveshaft onto transmission →
- 39 FINAL DRIVE, DIFFERENTIAL for REAR FINAL DRIVE
- 39 - FINAL DRIVE, DIFFERENTIAL for REAR FINAL DRIVE 0AR
.
Install exhaust system free of stress →
- 26 - EXHAUST SYSTEM, EMISSION CONTROLS for 1.8 LITER 4-CYL. 5V TURBO ENGINE MECHANICAL, ENGINE CODE(S): AMB
- 26 - EXHAUST SYSTEM, EMISSION CONTROLS for 2.0 LITER 4-CYL. 4V TURBO ENGINE MECHANICAL, ENGINE CODE(S): BPG, BWT
- 26 EXHAUST SYSTEM, EMISSION CONTROLS for 3.0 LITER 6-CYL. 5V ENGINE MECHANICAL, ENGINE CODE(S): AVK, BGN
- 26 - EXHAUST SYSTEM, EMISSION CONTROLS for 3.2 V6 4V ENGINE MECHANICAL, ENGINE CODE(S): BKH
- 26 - EXHAUST SYSTEM, EMISSION CONTROLS for 4.2 LITER V8 4V ENGINE MECHANICAL, ENGINE CODE(S): BNS
- 26 - EXHAUST SYSTEM, EMISSION CONTROLS for 4.2 LITER V8 4V ENGINE MECHANICAL, ENGINE CODE(S): BNS
.

Tightening torques

Component	Nm
Cover (bottom) to selector mechanism	10
Selector lever cable to support bracket	12
Support bracket to transmission	10