SUBFRAME Mount Overview
- Bolt
- 40 Nm plus an additional 90° turn
- Replace
- Transmission support to transmission
- Bolts
- 50 Nm plus an additional 90° turn
- Replace
- Pendulum support to transmission
- Different lengths and tightening specifications
- Engine Support
- There are different versions.
- Bolt
- Engine support to engine
- Different lengths
- Tightening specification, refer to [For engine(s) CETA, CCTA] Specifications or to [For engine(s) CDMA] Specifications or to [For engine(s) CBRA] Specifications or to [For engine(s) BPY] Specifications
- Engine Mount
- With support arm
- Bolt
- Engine mount to body
- Tightening specification, refer to [For engine(s) CETA, CCTA] Specifications or to [For engine(s) CDMA] Specifications or to [For engine(s) CBRA] Specifications or to [For engine(s) BPY] Specifications
- Connecting Bar
- Bolt
- Connecting bar to body
- Tightening specification, refer to [For engine(s) CETA, CCTA] Specifications or to [For engine(s) CDMA] Specifications or to [For engine(s) CBRA] Specifications or to [For engine(s) BPY] Specifications
- Bolt
- Connecting bar to engine
- Tightening specification, refer to [For engine(s) CETA, CCTA] Specifications or to [For engine(s) CDMA] Specifications or to [For engine(s) CBRA] Specifications or to[For engine(s) BPY] Specifications
- Bolt
- Engine mount to body
- Tightening specification, refer to [For engine(s) CETA, CCTA] Specifications or to [For engine(s) CDMA] Specifications or to [For engine(s) CBRA] Specifications or to [For engine(s) BPY] Specifications
- Bolts
- Engine mount to engine support
- Tightening specification, refer to [For engine(s) CETA, CCTA] Specifications or to [For engine(s) CDMA] Specifications or to [For engine(s) CBRA] Specifications or to [For engine(s) BPY] Specifications
- Pendulum Support
- Removing and Installing, refer to PENDULUM SUPPORT
- Bolt
- 100 Nm plus an additional 90° turn
- Replace
- Pendulum support to subframe
- Bolt
- 60 Nm plus an additional 90° turn
- Replace
- Transmission mount to transmission support
- Bolt
- 40 Nm plus an additional 90° turn
- Replace
- Transmission mount to chassis
- Transmission Mount
- With support arm
- Removing and Installing:
- Vehicles with 2.0L TFSI engine, refer to TRANSMISSION MOUNT AND TRANSMISSION SUPPORT
- Vehicles with 3.2L MPI engine, refer to TRANSMISSION MOUNT AND TRANSMISSION SUPPORT
- Tightening specification and sequence, refer to Fig 2
- Bolt
- 40 Nm plus an additional 90° turn
- Replace
- Transmission support to transmission
- Bolt
- 40 Nm plus an additional 90° turn
- Replace
- Transmission support to transmission
- Transmission Support
- Removing and Installing, refer to:
- Vehicles with 2.0L TFSI engine, refer to TRANSMISSION MOUNT AND TRANSMISSION SUPPORT
- Vehicles with 3.2L MPI engine, refer to TRANSMISSION MOUNT AND TRANSMISSION SUPPORT
- Tightening sequence, refer to Fig 2
- Removing and Installing, refer to:
-- Install the transmission support -A- between transmission and transmission mount support arm.
-- Mount the transmission support to the transmission.
-- Raise transmission to transmission mount support arm with engine support bridge 10 - 222 A spindle.
-- Next, install bolts -2-, but only hand tight.
CAUTION:
Risk of damaging the threads in the transmission support by inserting bolts crooked.
- Before installing bolts -2-, transmission support and transmission mount support arm must be absolutely parallel to each other. If necessary, raise rear of transmission with trolley jack.
-- Only tighten bolts if subframe is installed. Refer to Description and Operation and subframe mounts are adjusted [For engine(s) CETA, CCTA] Description and Operation or to [For engine(s) CDMA] Description and Operation or to [For engine(s) CBRA] Description and Operation or to [For engine(s) BPY] Description and Operation .