On Board Diagnostic (OBD) - Radio, Navigation, Steering & Telematics

• Radio, On Board Diagnostic (OBD)
  • General information
    • Technical features of radio systems
  • Radio On Board Diagnostic (OBD), initiating
    • Notes
    • Additional reference materials required
  • Safety precautions
    • If special testing equipment is required during test drive, note the following:
    • To reduce the risk of personal injury and/or damage of electric and electronic components, always observe the following:
    • Test requirements
    • On Board Diagnostic (OBD) functions
  • Control Module Versions, checking (function 01)
  • Diagnostic Trouble Code (DTC) Memory, checking (function 02)
  • Diagnostic Trouble Code (DTC) table
  • Output Diagnostic Test Mode (DTM) (function 03)
    • Notes
    • Output DTM, initiating
  • Diagnostic Trouble Code (DTC) Memory, erasing (function 05)
    • Notes
    • Requirements
  • End Output (function 06)
  • Code Control Module (function 07)
    • Notes
    • Coding procedure
    • Coding table - through m.y. 2001
    • Coding table - from m.y. 2002
  • Read Measuring Value Block (function 08)
    • Read Measuring Value Block, initiating
    • Summary of display groups - through m.y. 2001
    • Summary of display groups - from m.y. 2002
    • Display Group Tables
      • Notes
      • Display group 001 - through m.y. 2001
      • Display group 001 - from m.y. 2002
      • Display group 002 - through m.y. 2001
      • Display group 002 - from m.y. 2002
      • Display group 003
      • Display group 004 - through m.y. 2001
      • Display group 004 - from m.y. 2002
      • Display group 005 - through m.y. 2001
      • Display group 005 - from m.y. 2002
      • Display group 006 - through m.y. 2001
      • Display group 007 - through m.y. 2001
  • Adaptation (function 10)
    • Notes
    • Adaptation (function 10), initiating
      • Notes
      • Adaptation table:
    • Vehicle speed display, enable/disable
    • Long wave reception, enable/disable (where applicable)
    • Transport Mode, activate/deactivate
• Navigation system III (NS-Low) through m.y. 2001, On Board Diagnostic (OBD)
  • General information
    • Equipment features:
    • Function description
  • Navigation system III On Board Diagnostic (OBD), initiating
    • Notes
    • Additional reference materials required
  • Safety precautions
    • If special testing equipment is required during test drive, note the following:
    • To reduce the risk of personal injury and/or damage of electric and electronic components, always observe the following:
    • Test requirements:
    • On Board Diagnostic (OBD) functions
  • Control Module Versions, checking (function 01)
  • Diagnostic Trouble Code (DTC) Memory, checking (function 02)
  • Diagnostic Trouble Code (DTC) table
  • Output Diagnostic Test Mode (DTM) (function 03)
    • Notes
    • Output DTM, initiating
  • Diagnostic Trouble Code (DTC) Memory, erasing (function 05)
    • Notes
    • Requirements
  • End Output (function 06)
  • Read Measuring Value Block (function 08)
    • Read Measuring Value Block, initiating
    • Display group overview:
    • Display group 001
    • Display group 002
    • Display group 003
    • Display group 004
    • Display group 005
    • Display group 006
    • Display group 007
    • Display group 008
    • Display group 010
  • Function status register
    • Function description
    • Test requirements:
  • Adaptation (function 10)
    • Notes
    • Adaptation table:
    • Adaptation, initiating
    • Tire circumference, adapting
    • Impulse number/wheel rotation (GALA), checking
      • Notes
      • Tire table for Audi A6:
    • Production diagnostic function (function status register), enabling/disabling
    • Speaker connection, adapting
    • Country selection, adapting
• Navigation system IV (BNS 4.0) from m.y. 2002, On Board Diagnostic (OBD)
  • General information
    • Notes
    • Navigation IV - additional equipment features:
    • Navigation IV - additional function descriptions:
  • Navigation system IV On Board Diagnostic (OBD), initiating
    • Notes
    • Additional reference materials required
  • Safety precautions
    • If special testing equipment is required during test drive, note the following:
    • To reduce the risk of personal injury and/or damage of electric and electronic components, always observe the following:
    • Test requirements:
    • On Board Diagnostic (OBD) functions
  • Control Module Versions, checking (function 01)
  • Diagnostic Trouble Code (DTC) Memory, checking (function 02)
  • Diagnostic Trouble Code (DTC) table
  • Output Diagnostic Test Mode (DTM) (function 03)
    • Notes
    • Output DTM, initiating
  • Diagnostic Trouble Code (DTC) Memory, erasing (function 05)
    • Notes
    • Requirements
  • End Output (function 06)
  • Read Measuring Value Block (function 08)
    • Read Measuring Value Block, initiating
    • Display group overview:
    • Display group 001
    • Display group 002
    • Display group 003
    • Display group 004
    • Display group 005
    • Display group 006
    • Display group 007
    • Display group 008
    • Display group 010
  • Function status register
    • Function description
    • Test requirements:
  • Adaptation (function 10)
    • Notes
    • Adaptation, initiating
    • Adaptation table:
    • Tire circumference, adapting
    • Impulse number/wheel rotation (GALA), checking
      • Notes
      • Tire table for Audi A6:
    • Production diagnostic function (function status register), enabling/disabling
    • Speaker connection, adapting
    • Country selection, adapting
    • Dynamic route guidance (where applicable), adapting
• Multi-function steering wheel, On Board Diagnostic (OBD)
  • General information
    • Technical features
      • Notes
      • Control module/equipment versions through m.y. 2001:
      • Control module/equipment versions from m.y. 2002:
  • Multi-function steering wheel On Board Diagnostic (OBD), initiating
    • Notes
    • Additional reference materials required
  • Safety precautions
    • If special testing equipment is required during test drive, note the following:
    • To reduce the risk of personal injury and/or damage of electric and electronic components, always observe the following:
    • Test requirements:
    • On Board Diagnostic (OBD) functions
  • Control Module Versions, checking (function 01)
  • Diagnostic Trouble Code (DTC) Memory, checking (function 02)
  • Diagnostic Trouble Code (DTC) table
  • Output Diagnostic Test Mode (DTM) (function 03)
    • Notes
    • Output DTM, initiating
  • Diagnostic Trouble Code (DTC) Memory, erasing (function 05)
    • Notes
    • Requirements
  • End Output (function 06)
  • Code Control Module (function 07)
    • Notes
    • Code control module, initiating
    • Coding tables through m.y. 2001
      • Control module suffix "D" & "E"
      • Control module suffix "L"
    • Coding tables from m.y. 2002
      • Control module suffix "C"
      • Control module suffix "J"
      • Control module suffix "F" & "H"
  • Read Measuring Value Block (function 08)
    • Read Measuring Value Block, initiating
    • Display group overview:
    • Display group 001
    • Display group 002
    • Display group 003
• Telematics, On Board Diagnostic (OBD)
  • General information
    • Telematics, technical features
  • Telematics On Board Diagnostic (OBD), initiating
    • Notes
    • Additional reference materials required
  • Safety precautions
    • If special testing equipment is required during test drive, note the following:
    • To reduce the risk of personal injury and/or damage of electric and electronic components, always observe the following:
    • Test requirements
    • On Board Diagnostic (OBD) functions
    • Scan tool display texts
  • Control Module Versions, checking (function 01)
  • Diagnostic Trouble Code (DTC) Memory, checking (function 02)
  • Diagnostic Trouble Code (DTC) Table
  • Output Diagnostic Test Mode (DTM) (function 03)
    • Notes
    • Output DTM, initiating:
  • Diagnostic Trouble Code (DTC) Memory, erasing (function 05)
    • Notes
    • Requirements
  • End Output (function 06)
  • Code Control Module (function 07)
    • Notes
    • Code Control Module, initiating
    • Coding table:
  • Read Measuring Value Block (function 08)
    • Read Measuring Value Block, initiating
    • Display group overview:
    • Display group 001
    • Display group 002
    • Display group 003
    • Display group 004
    • Display group 005
    • Display group 020
    • Display group 021
    • Display group 022
    • Display group 023
    • Display group 024
    • Display group 025
    • Display group 026
    • Display group 027
    • Display group 028
    • Display group 029
    • Display group 030
    • Display group 078
    • Display group 079
    • Display group 080
    • Display group 125
    • Display group 126
  • Adaptation (function 10)
    • Notes
    • Adaptation (function 10), initiating
    • Adaptation table:
    • Transport Mode, activating/deactivating
    • Example: Deactivate Transport Mode
    • Emergency (back-up) battery, switch on/off, reset time register
    • Emergency (back-up) battery adaptation examples:
    • Example: Switch off emergency (back-up) battery
    • Example: Switch on emergency (back-up) battery
    • Example: Reset emergency (back-up) battery time register
• VAS 5051 tester or VAG 1551/1552 Scan Tool (ST), connecting
  • Test conditions
  • Through m.y. 2001:
  • From m.y. 2001:
  • VAG 1551 Scan Tool use: