Special Tools
WARNING: This page is about a different car, the 2017 Volkswagen GTI, 2016 Volkswagen GTI, 2015 Volkswagen Golf, and 2015 Volkswagen GTI. However, it is still accessible from the selected car via links, so may be relevant.
Special Tools And Workshop Equipment Required
- Slide Hammer Set - Adapter 40:VW771/40
- Engine Support Brackets:T40093/3-6 (quantity 2)
- Engine Support Bridge - Special Hook (2 pc.):10-222A/20
- Engine Support - Basic Set - Square Pipe:T40091/1 (quantity 2)
- Engine Support - Basic Set - Movable Joint:T40091/3 (quantity 2)
- Engine Support - Supplement Kit - Spindle:T40093/3 (quantity 2) from the Engine Support - Supplement Kit:T40093A
- Engine Sling - Engine Bracket:2024A/1 from Engine Sling:2024A
Special Tools And Workshop Equipment Required
- Bearing Driver - Multiple Use:VW244B
- Transmission Support:VW353
- Press Plate:VW401
- Press Plate:VW402
- Press Piece - Rod:VW407
- Press Piece - 37mm:VW416B
Special Tools And Workshop Equipment Required
- Guide Pin:VW436A
- Press Piece - Guide Pin:VW439
- Slide Hammer Set:VW771
- Crankshaft Holding Fixture:VW801
- Guide Pins:10-15
- Press Piece - Pivot Mount Bushing:3124
Special Tools And Workshop Equipment Required
- Bearing Installer - Crankshaft Pilot Bearing:3264
- Subframe Support Tool:3290
- Torque Wrench 5-50 Nm :VAG1331
- Bushing Driver - Selector Shaft:T10168
- Locking Sleeve Drift:T10169 or Locking Sleeve Drift:T10362 . Refer to Lock Sleeve Differentiation
- Breather Tube Tool:T10203
Special Tools And Workshop Equipment Required
- Holding Plate:VW309A
- or Holding Plate:VW309A
- Holding Fixture:VW313
- Transmission Support:VW353
- Press Piece - Multiple Use:VW455 or Press Piece - Front Wishbone:3160
- Slide Hammer Set:VW771
- -1- Puller - Kukko Internal - 12-16mm:21/1
- -3- Puller - Kukko Quick Action Separating Tool - 5-60mm:17/0
- -4- Puller - Kukko Counterstay:22/1
- -4- Counter Support:VAS251621
Special Tools And Workshop Equipment Required
- Press Piece - Rod:VW407
- Bushing Driver - Selector Shaft:T10168
- Seal Installer - Driveshaft:T40008
- -1- Puller - Kukko Internal - 14-19mm:21/2
- -1- Puller - Kukko Internal - 20-30mm:21/4
- -4- Puller - Kukko Counterstay:22/1
- -4- Puller - Kukko Counterstay:22/2
- -4- Counter Support:VAS251623
Special Tools And Workshop Equipment Required
- Transmission Support - Mounting Plate 33:3282/33
- Support Elements for transmission (determine when mounting the Mounting Plate on the Transmission Support)
- Transmission Support Jig:3336 to transport the transmission.
- Torque Wrench 1331 5-50 Nm :VAG1331
- Torque Wrench 1332 40-200 Nm :VAG1332
- Engine and Gearbox Jack:VAS6931
Special Tools And Workshop Equipment Required
- Bracket - Multiple Use:30-211A
- Seal Installer - Drive Flange:T10143 or Seal Installer - Output Shaft Oil Seal:T10180
- Locking Sleeve Drift:T10169
- or Locking Sleeve Drift: T10362 . Refer to Lock Sleeve Differentiation
- Seal Installer - Driveshaft:T40008
- Torque Wrench 1331 5-50 Nm :VAG1331
- Hot Air Blower:VAG1416
Special Tools And Workshop Equipment Required
- Engine Support Bridge:10-222A
- Engine/Gearbox Support Shackle (2 pc.):10-222A/12
- Engine Support Bridge - Engine Support 31 - Adapter 1:10-222A/31-1
- Engine Support Bridge - Engine Support 31 - Adapter 2:10-222A/31-2
- Engine Support - Basic Set - Square Pipe:T40091/1
- Engine Support - Basic Set - Movable Joint:T40091/3
- Engine Support Brackets:T40093/3 from Engine Support - Supplement Kit:T40093A
- Engine Support Brackets:T40093/3-6
- Transmission Support:3282
Special Tools And Workshop Equipment Required
- Engine Support Bridge:10-222A
- Engine Support Bridge - Engine Support 29:10-222A/29
- Engine Support Bridge - Engine Support 18:10-222A/18
- If necessary Engine/Gearbox Support Shackle (2 pc.):10-222A/12
- Transmission Support:3282
- Transmission Support - Pins 29:3282/29
Special Tools And Workshop Equipment Required
- Hex Ball Socket:3247
- Socket And Extended Bit:T10107A
- Counterhold - Multiple Use:T10172A
- Spindle Cover:T10381
- Torque Wrench 1331 5-50 Nm :VAG1331
- Engine Support:T50015A
- Not needed: Engine Support Device - Gearbox Bracket:T10346/1
- M8 X 25 bolt
Special Tools And Workshop Equipment Required
- Used Oil Collection and Extraction Unit:SMN372500
- Holding Fixture - Gearbox Adapter:T10235
- Connecting Pin:T10027A
- Wedge Set:T10383
- Puller - Crankshaft/Power Steering Seal 1:T20143/1
- Hose Clip Pliers:VAG1275A
- Engine and Gearbox Bracket:VAS6095A
- Shop Crane:VAS6100
- Engine Bung Set:VAS6122
- Shop Crane - Drip Tray:VAS6208
- Press Piece - Shift Rod/Alternator:VW423
- -1- Puller - Kukko Internal - 14-19mm:21/2
- -1- Puller - Kukko Internal - 20-30mm:21/4
- -4- Counter Support:VAS251623
- Thread adaptor from Puller - Kukko Counterstay:22/1
- -1- Internal Puller:VAS251605
(21-2)
- -1- Internal Puller:VAS251609 (21-4)
- -4- Counter Support:VAS251623 (22-2)
- Thread adapter from Counter Support:VAS251621 (22-1)
- Pry Lever:80-200
- Hose Clamps - Up To 25mm:3094
- Transmission Support Jig:3336
- Triple Square Socket Driver:3357
.
- Backrest Panel Tool:3370