LEMON Manuals: Even more car manuals for everyone
Home >> Volkswagen >> 2005 >> Jetta TDI, Automatic >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 17 (Brake System - OBD (A4 Platform)) >> 01 On Board Diagnostic (OBD) >> ABS Mark 60 On Board Diagnostic (OBD), vehicles from my 10.00 >> Troubleshooting with V.A.G 1551 scan tool or tester VAS 5051 on ABS Mark 60 (flow chart)

Troubleshooting with V.A.G 1551 scan tool or tester VAS 5051 on ABS Mark 60 (flow chart)

WARNING: This page is about a different variant/trim than selected.
                                Start                     
          Connect V.A.G 1551 Scan Tool and select 1-rapid data transfer ← or → Connect tester VAS 5051 and select vehicle self-diagnosis    
                            ↓           ↓              
    Compare control module identification ← ← ← ← ← Select address word 03-Brake electronics        
    ↓                                   ↓              
    ↓               ← ← ← ← ← ← ← Check DTC memory 02        
    ↓               ↓                   ↓              
    ↓       Correct DTCs using DTC table       No DTCs recognized        
    ↓         ↓         ↓                   ↓          
    ↓
↓		     Read measured value block 08     Perform output Diagnostic Test Mode (DTM) 03       ↓
↓		          
    ↓     ↓       ↓       ↓                 ↓          
    ↓   Replace comp.   ↓       ↓   1. Perform test drive at more than 20 km/h    
    ↓     ↓       ↓       ↓   2. Check DTC memory 02 again    
    ↓     ↓       ↓       ↓   3. "No DTCs recognized" is displayed again    
    ↓     ↓       ↓       ↓                 ↓          
    A      B       C       D                  E           
    A    B         C       D                  E           
    ↓   ↓         ↓       ↓                 ↓          
    ↓
↓
↓
↓		   ↓
↓
↓
↓		   Perform directed entry of electrical tests     Service hydraulic/mechanical parts of brake system (Refer to 47 BRAKES - HYDRAULIC COMPONENTS and 47 BRAKES - HYDRAULIC COMPONENTS )       ↓
↓
↓
↓		          
    ↓   ↓         ↓         ↓               ↓          
    ↓   → → → → → ↓         ↓               ↓          
    ↓
↓		             ↓
↓		         ↓
↓		   1. Perform all test steps of electrical checks. Refer to Electrical check of Mark 60     
    Identification not OK.   ↓
↓		         ↓
↓		   2. Service hydraulic/mechanical parts of brake system    
          ↓       ↓         ↓     (Refer to BRAKE SYSTEM )    
    Replace control module   ↓         ↓               ↓          
          ↓       ↓         ↓               ↓          
       
  • Connect V.A.G 1551 scan tool or tester VAS 5051 and check DTC memory 02.
    
       
  • Erase DTC memory (05)
    
       
  • Perform test drive at more than 20 km/h (13 mph) and allow the ABS regulate braking.
    
       
  • Check DTC memory after test drive. If "No DTC recognized" appears on display of V.A.G 1551 scan tool or tester VAS 5051 after repair DTCs and perform test drive, the On Board Diagnostic (OBD) is completed.
    
scientia non olet · About LEMON Manuals