LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2025 >> Prius Plug-In Hybrid SE >> Repair and Diagnosis >> Body & Frame >> Exterior/Interior Trim >> Interior Panels / Trim - Service Information (2 Of 2) >> Roof Headlining >> Removal [03/2023 - ] >> Procedure

Removal [03/2023 - ]: Procedure

  1. REMOVE TONNEAU COVER ASSEMBLY 
    1. GTY1142594Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. REMOVE DECK BOARD ASSEMBLY 
    1. GTY1158371Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A for Type A *B for Type B
  3. REMOVE DECK FLOOR BOX RH 

    HINT: 

    As the illustration shown is an example, the actual details may differ.

    1. w/o Spare Tire:
      GTY1150285Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A for Type A *B for Type B
    2. w/ Spare Tire:
      GTY1158088Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. REMOVE DECK FLOOR BOX LH 

    HINT: 

    As the illustration shown is an example, the actual details may differ.

    1. w/o Spare Tire:
      GTY1139645Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A for Type A *B for Type B
    2. w/ Spare Tire:
      GTY1158086Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. REMOVE BATTERY SERVICE HOLE COVER ASSEMBLY (w/ Battery Cover) 

    HINT: 

    As the illustration shown is an example, the actual details may differ.

    1. GTY1139597Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here Remove in this Direction (1)
      Remove in this Direction (2) - -
  6. REMOVE FRONT SEAT ASSEMBLY LH 
    1. for Manual Seat:

      Refer to REMOVAL [03/2023 - ]

    2. for Power Seat:

      Refer to REMOVAL [03/2023 - ]

  7. REMOVE FRONT SEAT ASSEMBLY RH 
    1. Use the same procedure as for the LH side.
  8. REMOVE REAR SEAT ASSEMBLY 

    Refer to REMOVAL [03/2023 - ]

  9. REMOVE REAR CONSOLE BOX ASSEMBLY 

    Refer to REMOVAL [03/2023 - ]

  10. REMOVE FRONT DOOR SCUFF PLATE LH 
    1. GTY1143204Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here Remove in this Direction (1)
      Remove in this Direction (2) - -
  11. REMOVE COWL SIDE TRIM BOARD LH 
    1. GTY1156613Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
  12. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH 

    Refer to PROCEDURE - Step 3

  13. REMOVE FRONT PILLAR GARNISH LH 
    1. GTY1151458Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Roof Headlining Assembly *2 Front Pillar Garnish Clip
      Pull in this Direction - -
      1. Pull the upper part of the front pillar garnish LH toward the inside of the cabin as shown in the illustration to disengage the front pillar garnish LH from the base of the 2 front pillar garnish clips.

        HINT: 

        • Let the front pillar garnish LH hang from the 2 front pillar garnish clips.
        • Separate the front pillar garnish LH in such a way that the front pillar garnish clip does not contact the roof headlining assembly.
    2. GTY1155688Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Pull in this Direction Pull in this Direction
      1. Pull down the front pillar garnish clip while pushing the side of the release lever with SST as shown in the illustration.
        • SST: 09813-00020 
      2. While pulling the front pillar garnish clip, push the side of the release lever with SST as shown in the illustration and then separate the front pillar garnish clip from the vehicle body.
    3. GTY1151116Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
      1. Disengage the 2 guides to remove the front pillar garnish LH as shown in the illustration.
    4. GTY1156198Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Protect the curtain shield airbag assembly LH.

        1. Cover the curtain shield airbag assembly LH with a protective cover, such as a cloth, and secure the edges of the cover with tape as shown in the illustration.

        NOTE:

        Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.

    5. GTY1151554Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Remove the 2 front pillar garnish clips from the front pillar garnish LH.
  14. REMOVE REAR DOOR SCUFF PLATE INSIDE LH 
    1. GTY1159112Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here Remove in this Direction
    2. GTY1154120Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here Remove in this Direction
    3. GTY1140787Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
  15. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH 

    Refer to PROCEDURE - Step 2

  16. REMOVE REAR UNDER SIDE COVER LH (for HEV Model) 
    1. GTY1141974Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
  17. REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side) 

    Refer to PROCEDURE - Step 8

  18. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH 

    Refer to PROCEDURE - Step 9

  19. REMOVE CENTER PILLAR LOWER GARNISH LH 
    1. GTY1157543Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here Remove in this Direction
  20. REMOVE CENTER PILLER GARNISH ASSEMBLY LH 
    1. GTY1152340Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
  21. REMOVE FRONT DOOR SCUFF PLATE RH 
    1. Use the same procedure as for the LH side.
  22. REMOVE COWL SIDE TRIM BOARD RH 
    1. Use the same procedure as for the LH side.
  23. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH 
    1. Use the same procedure as for the LH side.
  24. REMOVE FRONT PILLAR GARNISH RH 
    1. Use the same procedure as for the LH side.
  25. REMOVE REAR DOOR SCUFF PLATE INSIDE RH 
    1. Use the same procedure as for the LH side.
  26. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH 
    1. Use the same procedure as for the LH side.
  27. REMOVE REAR UNDER SIDE COVER RH (for HEV Model) 
    1. Use the same procedure as for the LH side.
  28. REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side) 
    1. Use the same procedure as for the LH side.
  29. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH 
    1. Use the same procedure as for the LH side.
  30. REMOVE CENTER PILLAR LOWER GARNISH RH 
    1. Use the same procedure as for the LH side.
  31. REMOVE CENTER PILLAR GARNISH ASSEMBLY RH 
    1. Use the same procedure as for the LH side.
  32. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH 
    1. GTY1141014Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  33. REMOVE REAR SEAT SIDE GARNISH LH 
    1. GTY1145439Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Remove the bolt.
    2. GTY1146281Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Place Hand Here Remove in this Direction (1)
      Remove in this Direction (2) - -
      1. Disengage the claw as shown in the illustration.
      2. Disengage the claw and guide.
    3. GTY1149576Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Disengage the clamp.
      2. Disconnect the airbag connector to remove the rear seat side garnish LH.
        NOTE:

        When disconnecting any airbag connector, take care not to damage the airbag wire harness.

        HINT: 

        Refer to How to Connect or Disconnect Airbag Connector.

        Refer to HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR [12/2022 - ]

  34. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side) 
    1. GTY1142313Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  35. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for Rear Side) 
    1. GTY1142312Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  36. REMOVE REAR DECK TRIM COVER 
    1. GTY1142311Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  37. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH 
    1. GTY1152616Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Perform the following procedure to remove the deck trim side panel assembly LH.

        1. Disengage the 2 clips.

        2. Disengage the 7 claws and guide as shown in the illustration.

      2. w/ Power Outlet Socket:
        GTY1149442Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        1. Disconnect the connector.

  38. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH 
    1. GTY1150270Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
  39. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY RH 
    1. Use the same procedure as for the LH side.
  40. REMOVE REAR SEAT SIDE GARNISH RH 
    1. Use the same procedure as for the LH side.
  41. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side) 
    1. Use the same procedure as for the LH side.
  42. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY 
    Refer to PROCEDURE - Step 1
  43. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH 
    1. Use the same procedure as for the LH side.
  44. REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH 
    1. Use the same procedure as for the LH side.
  45. REMOVE VISOR ASSEMBLY LH 
    1. GTY1142323Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  46. REMOVE VISOR ASSEMBLY RH 
    1. Use the same procedure as for the LH side.
  47. REMOVE ASSIST GRIP COVER 
    1. GTY1153272Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a 30 to 45° - -
      Remove in this Direction - -
      1. Insert SST into the cutout of the assist grip cover as shown in the illustration.
        • SST: 09813-00010 
        NOTE:

        To prevent the assist grip assembly from being damaged, make sure to insert SST straight into the cutout.

      2. Pull SST as shown in the illustration to disengage the claw.
        NOTE:

        To prevent the assist grip assembly from being damaged, make sure to only pull SST as shown in the illustration.

        HINT: 

        Use the same procedure for the claw on the other side of the assist grip cover.

      3. Remove the assist grip cover.
    2. Use the same procedure for all assist grip covers.
  48. REMOVE ASSIST GRIP 
    1. GTY1148530Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *A for LH Side *B for RH Side
      Remove in this Direction - -
  49. REMOVE REAR ASSIST GRIP LH 
    1. Use the same procedure as for the assist grip.
  50. REMOVE REAR ASSIST GRIP RH 
    1. Use the same procedure as for the assist grip.
  51. REMOVE MAP LIGHT ASSEMBLY 

    Refer to PROCEDURE - Step 1

  52. REMOVE VANITY LIGHT ASSEMBLY 
    Refer to PROCEDURE - Step 1
  53. REMOVE SPOT LIGHT ASSEMBLY 
    Refer to PROCEDURE - Step 1
  54. REMOVE NO. 2 FORWARD RECOGNITION COVER 
    Refer to PROCEDURE - Step 1
  55. REMOVE NO. 1 FORWARD RECOGNITION COVER 
    Refer to PROCEDURE - Step 2
  56. REMOVE RAIN SENSOR (w/ Rain Sensor) 

    Refer to REMOVAL [12/2022 - ]

  57. REMOVE ROOF CENTER REINFORCEMENT PROTECTOR (for Panoramic Moon Roof) 
    1. GTY1138605Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  58. DISCONNECT FRONT DOOR CHECK ASSEMBLY (for Front Passenger Side) 
    1. GTY1148011Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  59. REMOVE ROOF HEADLINING ASSEMBLY 
    1. GTY1145094Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      As the illustration shown is an example, the actual details may differ.

      1. for Front Pillar LH Side:

        1. Remove the protective cover.

        2. Disconnect each connector.

        3. Disengage the 3 clamps.

        4. Install the protective cover.

      2. for Front Pillar RH Side:

        1. Remove the protective cover.

        2. Disconnect each connector.

        3. Disengage the 2 clamps.

        4. Install the protective cover.

      3. for Windshield Glass Side:

        1. Disconnect each connector.

      4. for Map Light Side:

        1. Disconnect the connector.

      5. for Rear Pillar LH Side:

        1. Disconnect the connector.

      6. for Rear Pillar RH Side:

        1. Disconnect each connector.

        2. Disengage the clamp.

    2. GTY1156430Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Rotation Direction Remove in this Direction (1)
      Remove in this Direction (2) - -
      1. Turn each visor holder approximately 45° and remove them as indicated by the arrows, in the order shown in the illustration.
      2. Disengage the 4 claws as shown in the illustration to remove the base of each visor holder.
    3. for Normal Roof:
      GTY1151739Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction - -
      1. Disengage the 2 clips to remove the roof headlining assembly.
      2. Remove the roof headlining assembly from the vehicle through the front passenger side as shown in the illustration.
        NOTE:

        Do not damage the roof headlining assembly or vehicle interior.

    4. for Panoramic Moon Roof:
      GTY1155726Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Fastener - -
      Remove in this Direction - -
      1. Disengage the 2 clips.
      2. Disengage the 12 fasteners to remove the roof headlining assembly.
      3. Remove the roof headlining assembly from the vehicle through the front passenger side as shown in the illustration.
        NOTE:

        Do not damage the roof headlining assembly or vehicle interior.

scientia non olet · About LEMON Manuals