LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2024 >> Corolla LE >> Repair and Diagnosis >> External Pages >> Different car >> Section 300 (Engine Control System (2ZR-FAE) - Diagnostic Codes (1 Of 8)) >> SFI System >> DTC P0107: Manifold Absolute Pressure / Barometric Pressure Circuit Low Input; DTC P0108: Manifold Absolute Pressure / Barometric Pressure Circuit High Input [03/2019 - 11/2022] >> Procedure

DTC P0107: Manifold Absolute Pressure / Barometric Pressure Circuit Low Input; DTC P0108: Manifold Absolute Pressure / Barometric Pressure Circuit High Input [03/2019 - 11/2022]: Procedure

WARNING: This page is about a different car, the 2022 Toyota Corolla, 2021 Toyota Corolla, 2020 Toyota Corolla, and 2019 Toyota Corolla. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR) 
    GTY838771Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    *a Front view of wire harness connector
    (to Manifold Absolute Pressure Sensor)

    HINT: 

    Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.

    1. Disconnect the manifold absolute pressure sensor connector.
    2. Turn the ignition switch to ON.
    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition
      C115-3 (VC) - C115-1 (E2) Ignition switch ON 4.75 to 5.25 V
      C115-2 (PIM) - C115-1 (E2) Ignition switch ON 3.0 to 5.25 V
    4. Turn the ignition switch off and wait for at least 30 seconds.
    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C115-3 (VC) - C115-2 (PIM) Ignition switch off 171 to 189 kΩ
      C115-1 (E2) - Body ground Always Below 1 Ω

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR 

    Refer to REMOVAL [01/2019 - 11/2022]

    Result: 

    NG 

    See step  2

  2. CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM) 
    1. Disconnect the manifold absolute pressure sensor connector.
    2. Disconnect the ECM connector.
    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      C115-3 (VC) - C77-77 (VCPM) Always Below 1 Ω
      C115-1 (E2) - C77-76 (EPIM) Always Below 1 Ω
      C115-2 (PIM) - C77-78 (PIM) Always Below 1 Ω
      C115-2 (PIM) or C77-78 (PIM) - Body ground and other terminals Always 10 kΩ or higher

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE ECM 

    Refer to REMOVAL [03/2019 - 09/2022] , or refer to REMOVAL [09/2022 - 11/2022]

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

scientia non olet · About LEMON Manuals