LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2024 >> Corolla LE >> Repair and Diagnosis >> External Pages >> Different car >> Section 267 (Engine Lubrication System - Service Information) >> Oil Pump >> Removal [11/2022 - 09/2024] >> Procedure

Removal [11/2022 - 09/2024]: Procedure

WARNING: This page is about a different car, the 2025 Toyota GR Corolla, 2024 Toyota GR Corolla, and 2023 Toyota GR Corolla. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE FRONT WHEELS 

    Refer to REMOVAL [09/2022 - ]

  2. REMOVE REAR ENGINE UNDER COVER RH 

    Refer to PROCEDURE - Step 19

  3. REMOVE FRONT BUMPER ASSEMBLY (w/ Engine Under Cover Air Guide) 

    Refer to REMOVAL [09/2022 - 08/2023] , or refer to REMOVAL [08/2023 - 09/2024]

  4. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH (w/ Engine Under Cover Air Guide) 

    Refer to PROCEDURE - Step 2

  5. DRAIN WASHER FLUID (w/ Engine Under Cover Air Guide) 

    Refer to PROCEDURE - Step 4

  6. REMOVE INLET HOSE (w/ Engine Under Cover Air Guide) 

    Refer to PROCEDURE - Step 6

  7. REMOVE WINDSHIELD WASHER JAR ASSEMBLY (w/ Engine Under Cover Air Guide) 

    Refer to PROCEDURE - Step 7

  8. REMOVE NO. 2 ENGINE UNDER COVER AIR GUIDE (w/ Engine Under Cover Air Guide) 

    Refer to PROCEDURE - Step 8

  9. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 9

  10. REMOVE FAN AND GENERATOR V BELT 

    Refer to PROCEDURE - Step 3

  11. REMOVE COMPRESSOR ASSEMBLY WITH PULLEY 

    Refer to PROCEDURE - Step 17

  12. REMOVE NO. 1 AIR TUBE 
    1. Remove the 2 bolts.
      GTY1107840Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Loosen the 2 hose clamps to remove the No. 1 air tube from the No. 2 air hose and No. 3 air hose.
  13. REMOVE NO. 2 AIR HOSE 
    1. Loosen the hose clamp to remove the No. 2 air hose from the turbocharger sub-assembly.
      GTY1109322Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. DISCONNECT ENGINE WIRE 
    1. Remove the bolt and disconnect the engine wire from the timing chain cover assembly.
      GTY1019842Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY 

    Refer to PROCEDURE - Step 67

  16. REMOVE TIMING GEAR COVER INSULATOR 
    1. Remove the timing gear cover insulator from the timing chain cover assembly.
      GTY1019843Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  17. REMOVE CRANKSHAFT PULLEY ASSEMBLY 

    Refer to PROCEDURE - Step 14

  18. REMOVE TIMING CHAIN COVER ASSEMBLY 
    1. Remove the 12 bolts and seal washer.
      GTY1019844Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the timing chain cover assembly by prying between the timing chain cover assembly and oil pan sub-assembly, cylinder block sub-assembly with a screwdriver with its tip wrapped with protective tape.
      GTY1020470Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the 2 oil pump gaskets from the cylinder block sub-assembly.
      GTY1019845Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Be careful not to damage the contact surfaces of the oil pan sub-assembly.

  19. REMOVE TIMING CHAIN COVER OIL SEAL 

    Refer to PROCEDURE - Step 21

scientia non olet · About LEMON Manuals