LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2022 >> RAV4 LE, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 111 (Automatic Transaxle System (UB80F) - Service Information (2 Of 3)) >> Transmission Control Cable >> Installation [08/2020 - ] >> Procedure

Installation [08/2020 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY 
    1. Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.

      Torque: 6.0 N.m (61 kgf/cm, 53 in.lbf) 

    2. Connect the transmission control cable assembly to the vehicle body with the nut.

      Torque: 6.0 N.m (61 kgf/cm, 53 in.lbf) 

      GTY921429Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Align the hole on the transmission control cable bracket with the protrusion of the vehicle body.
      NOTE:

      Do not deform the transmission control cable bracket.

    3. Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.
    4. Connect the transmission control cable assembly to the transmission control shaft lever as shown in the illustration.
      GTY934293Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Correct
      *b Incorrect
      NOTE:

      Before installing the transmission control cable assembly, check that the park/neutral position switch assembly and shift lever are in N.

  2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY 

    See step  2

  3. INSTALL NO. 1 CONSOLE BOX DUCT 

    See step  3

  4. INSTALL CONSOLE BOX ASSEMBLY 

    Refer to INSTALLATION [11/2018 - 12/2021] , or refer to INSTALLATION [12/2021 - ]

  5. INSTALL FRONT LOWER NO. 1 FLOOR HEAT INSULATOR 
    1. Install the front lower No. 1 floor heat insulator to the vehicle body with the 3 nuts.

      Torque: 4.9 N.m (50 kgf/cm, 43 in.lbf) 

  6. INSTALL FRONT FLOOR COVER RH 

    Refer to PROCEDURE - Step 11

  7. INSTALL FRONT FLOOR COVER LH 

    Refer to PROCEDURE - Step 13

  8. INSTALL FRONT EXHAUST PIPE ASSEMBLY 

    Refer to INSTALLATION [08/2020 - ]

  9. INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 99 [08/2020 - 12/2021] , or refer to PROCEDURE - Step 99 [12/2021 - ]

  10. INSTALL NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 100 [08/2020 - 12/2021] , or refer to PROCEDURE - Step 100 [12/2021 - ]

  11. INSTALL FRONT FENDER FRONT SPLASH SHIELD RH 

    Refer to PROCEDURE - Step 102 [08/2020 - 12/2021] , or refer to PROCEDURE - Step 101 [12/2021 - ]

  12. INSTALL FRONT FENDER FRONT SPLASH SHIELD LH 

    Refer to PROCEDURE - Step 101 [08/2020 - 12/2021] , or refer to PROCEDURE - Step 101 [12/2021 - ]

  13. INSTALL BATTERY CLAMP SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 71 [08/2020 - 12/2021] , or refer to PROCEDURE - Step 71 [12/2021 - ]

  14. INSTALL ECM 

    Refer to INSTALLATION [08/2020 - ]

  15. INSTALL BATTERY 

    Refer to INSTALLATION [11/2018 - 10/2023] , or refer to INSTALLATION [10/2023 - ]

  16. INSPECT SHIFT LEVER POSITION 

    See step  2

  17. ADJUST SHIFT LEVER POSITION 

    Refer to ADJUSTMENT [11/2018 - ] 

scientia non olet · About LEMON Manuals