LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Venza XLE >> Repair and Diagnosis >> Heating, Ventilation & A/C (HVAC) >> HVAC Control Systems >> Air Conditioning System - Service Information >> Compressor >> Removal [07/2020 - 10/2022] >> Procedure

Removal [07/2020 - 10/2022]: Procedure

  1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM 

    See step  1

  2. REMOVE SERVICE PLUG GRIP 

    Refer to REMOVAL [07/2020 - 10/2022]

  3. CHECK TERMINAL VOLTAGE 
    1. Remove the No. 2 inverter protector.

      Refer to PROCEDURE - Step 8

    2. Disconnect the engine room main wire.

      Refer to PROCEDURE - Step 9

    3. Remove the connector cover assembly.

      Refer to PROCEDURE - Step 10

    4. Check the terminal voltage.

      Refer to PROCEDURE - Step 11

    5. Install the connector cover assembly.

      Refer to PROCEDURE - Step 8

    6. Connect the engine room main wire.

      Refer to PROCEDURE - Step 16

    7. Install the No. 2 inverter protector.

      Refer to PROCEDURE - Step 17

  4. REMOVE FRONT FENDER FRONT SPLASH SHIELD LH 

    Refer to PROCEDURE - Step 7

  5. REMOVE FRONT FENDER FRONT SPLASH SHIELD RH 

    Refer to PROCEDURE - Step 8

  6. REMOVE NO. 1 ENGINE UNDER COVER 

    Refer to PROCEDURE - Step 9

  7. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY 

    Refer to PROCEDURE - Step 10

  8. REMOVE FRONT FENDER APRON SEAL RH 

    Refer to PROCEDURE - Step 12

  9. DISCONNECT SUCTION HOSE SUB-ASSEMBLY 
    1. Remove the bolt and disconnect the suction hose sub-assembly from the compressor with motor assembly.
      GTY990104Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the O-ring from the suction hose sub-assembly.
      NOTE:

      Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

      GTY990109Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE 
    1. Remove the bolt and disconnect the No. 1 cooler refrigerant discharge hose from the compressor with motor assembly.
      GTY990110Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the O-ring from the No. 1 cooler refrigerant discharge hose.
      NOTE:

      Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

      GTY990114Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  11. REMOVE COMPRESSOR WITH MOTOR ASSEMBLY 
    1. Slide the green-colored lock of the connector (A) as shown in the illustration to release it and disconnect the connector.
      GTY989841Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Connector (A) *b Connector (B)
      *c Green-colored Lock - -
      Slide - -
      WARNING:

      Make sure to wear insulated gloves.

      NOTE:

      Insulate the disconnected terminals and connector (A) with insulating tape.

    2. Disconnect the connector (B).
    3. Remove the bolt and 2 nuts.
      GTY990126Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Using an E8 "TORX" socket wrench, remove the 2 stud bolts.
      GTY990127Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the compressor with motor assembly as shown in the illustration.
      GTY990100Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
scientia non olet · About LEMON Manuals