LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> Venza LE >> Repair and Diagnosis >> Body & Frame >> Exterior Body Panels >> Exterior Panels / Trim - Service Information (2 Of 2) >> Rear Door Belt Moulding >> Removal [07/2020 - 10/2022] >> Procedure

Removal [07/2020 - 10/2022]: Procedure

  1. PRECAUTION 
    NOTE:

    After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Refer to BEFORE DISCONNECTING BATTERY [07/2020 - 10/2022]

  2. REMOVE REAR NO. 2 FLOOR BOARD 

    Refer to PROCEDURE - Step 2

  3. REMOVE BATTERY HOLE COVER 

    Refer to PROCEDURE - Step 6

  4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL 

    Refer to PROCEDURE - Step 4

  5. REMOVE REAR DOOR INSIDE HANDLE BEZEL 

    Refer to PROCEDURE - Step 5 [07/2020 - 12/2021] , or refer to PROCEDURE - Step 5 [12/2021 - 10/2022]

  6. REMOVE REAR DOOR ARMREST COVER 

    Refer to PROCEDURE - Step 6 [07/2020 - 12/2021] , or refer to PROCEDURE - Step 6 [12/2021 - 10/2022]

  7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 7 [07/2020 - 12/2021] , or refer to PROCEDURE - Step 7 [12/2021 - 10/2022]

  8. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP 

    Refer to PROCEDURE - Step 10 [07/2020 - 12/2021] , or refer to PROCEDURE - Step 10 [12/2021 - 10/2022]

  9. REMOVE REAR DOOR REAR BELT SEAL 

    Refer to PROCEDURE - Step 12 [07/2020 - 12/2021] , or refer to PROCEDURE - Step 12 [12/2021 - 10/2022]

  10. REMOVE REAR DOOR SERVICE HOLE COVER 

    Refer to PROCEDURE - Step 14 [07/2020 - 12/2021] , or refer to PROCEDURE - Step 14 [12/2021 - 10/2022]

  11. REMOVE REAR DOOR GLASS RUN 

    Refer to PROCEDURE - Step 16 [07/2020 - 12/2021] , or refer to PROCEDURE - Step 16 [12/2021 - 10/2022]

  12. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 17 [07/2020 - 12/2021] , or refer to PROCEDURE - Step 17 [12/2021 - 10/2022]

  13. REMOVE REAR DOOR QUARTER WINDOW GLASS 

    Refer to PROCEDURE - Step 18 [07/2020 - 12/2021] , or refer to PROCEDURE - Step 18 [12/2021 - 10/2022]

  14. REMOVE HOLE PLUG 

    Refer to PROCEDURE - Step 20 [07/2020 - 12/2021] , or refer to PROCEDURE - Step 20 [12/2021 - 10/2022]

  15. REMOVE REAR DOOR GLASS SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 21 [07/2020 - 12/2021] , or refer to PROCEDURE - Step 21 [12/2021 - 10/2022]

  16. REMOVE REAR DOOR BELT MOULDING ASSEMBLY 
    1. Apply protective tape around the rear door belt moulding assembly as shown in the illustration.
      GTY1013946Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Protective Tape
    2. Disengage the 7 claws to remove the rear door belt moulding assembly as shown in the illustration.
      GTY1014015Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      Remove in this Direction
scientia non olet · About LEMON Manuals