Disassembly [06/2020 - ]: Procedure
- REMOVE BENCH TYPE REAR SEAT CUSHION COVER
- Detach the hook.
- Using a thin-bladed screwdriver, detach the hook to remove the bench type rear seat cushion cover from the rear seat cushion pad as shown in the illustration.
Protective Tape - - NOTE:Be careful not to dirty or damage the bench type rear seat cushion cover.
HINT:
Tape the thin-bladed screwdriver tip before use.
- Detach the hook.
- REMOVE REAR SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)
Refer to PROCEDURE - Step 4
- REMOVE REAR SEAT CUSHION HEATER ASSEMBLY RH (w/ Seat Heater System)
Refer to PROCEDURE - Step 5
- REMOVE REAR SEAT HEADREST ASSEMBLY
- Remove the rear seat headrest assembly.
- REMOVE REAR LOWER SEATBACK LOCK BEZEL LH
- REMOVE REAR UPPER SEATBACK LOCK BEZEL LH
- REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH
- Detach the hook.
- Detach the hook.
- Pull out the 2 fasteners from the hole of rear seatback board sub-assembly LH.
- Open the 2 fasteners.
- Remove the clip.
- Remove the 2 clips.
- Pull in the removal direction (1) shown in the illustration to detach the claw.
*a Guide *b Hook Remove in this Direction (1) Remove in this Direction (2) Remove in this Direction (3) - Pull in the removal direction (2) shown in the illustration to detach the guide.
- Pull in the removal direction (3) shown in the illustration to detach the hook and remove the rear seatback board sub-assembly LH.
- Detach the hook.
- REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD
- REMOVE SEPARATE TYPE REAR SEATBACK COVER LH
- Using a thin-bladed screwdriver, detach the hook to remove the separate type rear seatback cover LH from the separate type rear seatback pad LH as shown in the illustration.
Protective Tape NOTE:Be careful not to dirty or damage the separate type rear seatback cover.
HINT:
Tape the thin-bladed screwdriver tip before use.
- Using a thin-bladed screwdriver, detach the hook to remove the separate type rear seatback cover LH from the separate type rear seatback pad LH as shown in the illustration.
- REMOVE REAR SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)
Refer to PROCEDURE - Step 12
- REMOVE REAR SEATBACK LOCK ASSEMBLY LH
- REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH
- REMOVE REAR SEAT HEADREST ASSEMBLY
- Remove the rear seat headrest assembly.
- REMOVE REAR CENTER SEAT HEADREST ASSEMBLY
- Remove the rear center seat headrest assembly.
- REMOVE SEAT BELT ANCHOR COVER CAP
- REMOVE REAR SEAT SHOULDER BELT COVER
- REMOVE REAR LOWER SEATBACK LOCK BEZEL RH
- REMOVE REAR UPPER SEATBACK LOCK BEZEL RH
- REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY RH
- Detach the hook.
- Detach the hook.
- Pull out the 2 fasteners from the hole of rear seatback board sub-assembly RH.
- Open the 2 fasteners.
- Remove the 2 clips.
- Pull in the removal direction (1) shown in the illustration to detach the claw.
*a Guide *b Hook Remove in this Direction (1) Remove in this Direction (2) Remove in this Direction (3) - Pull in the removal direction (2) shown in the illustration to detach the guide.
- Pull in the removal direction (3) shown in the illustration to detach the hook and remove the rear seatback board sub-assembly RH.
- Detach the hook.
- REMOVE CENTER ARMREST HINGE COVER
- Fold the rear center seat armrest assembly forward.
- Using a thin-bladed screwdriver, detach the claw on the rear side.
HINT:
Tape the thin-bladed screwdriver tip before use.
Remove in this Direction Protective Tape - Pull in the removal direction shown in the illustration and detach the claw and guide to remove the center armrest hinge cover.
- REMOVE REAR CENTER SEAT ARMREST ASSEMBLY
- Remove the bolt and washer.
- Return the rear center seat armrest assembly to rotate the outside location pin to the position as shown in the illustration.
*a Outside Location Pin - - Rotate - - - Detach the outside location pin in the removal direction (1) shown in the illustration.
*a Outside Location Pin *b Inside Location Pin Remove in this Direction (1) Remove in this Direction (2) - Detach the inside location pin in the removal direction (2) shown in the illustration and remove the rear center seat armrest assembly.
- Remove the rear seat armrest hinge shim.
- Remove the bolt and washer.
- REMOVE SEPARATE TYPE REAR SEATBACK COVER WITH PAD
- REMOVE SEPARATE TYPE REAR SEATBACK COVER RH
- Using a thin-bladed screwdriver, detach the hook to remove the separate type rear seatback cover RH from the separate type rear seatback pad RH as shown in the illustration.
Protective Tape NOTE:Be careful not to dirty or damage the separate type rear seatback cover.
HINT:
Tape the thin-bladed screwdriver tip before use.
- Using a thin-bladed screwdriver, detach the hook to remove the separate type rear seatback cover RH from the separate type rear seatback pad RH as shown in the illustration.
- REMOVE REAR SEATBACK HEATER ASSEMBLY RH (w/ Seat Heater System)
Refer to PROCEDURE - Step 24
- REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY
Refer to PROCEDURE - Step 15
- REMOVE REAR SEATBACK LOCK ASSEMBLY RH
- REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH