Removal [09/2019 - 08/2020]: Procedure

RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for HFC-134a(R134a))
Refer to PROCEDURE - Step 1
RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for HFO-1234yf(R1234yf))
Refer to PROCEDURE - Step 1
REMOVE HEADLIGHT ASSEMBLY LH (for Single Beam Headlight)
Refer to REMOVAL [09/2019 - 08/2020]
REMOVE HEADLIGHT ASSEMBLY RH (for Single Beam Headlight)
HINT:

Use the same procedure as for the LH side.
REMOVE HEADLIGHT ASSEMBLY LH (for Triple Beam Headlight)
Refer to REMOVAL [09/2019 - 12/2021]
REMOVE HEADLIGHT ASSEMBLY RH (for Triple Beam Headlight)
HINT:

Use the same procedure as for the LH side.
REMOVE NO. 1 AIR CLEANER INLET
Refer to PROCEDURE - Step 6
REMOVE FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY
Refer to PROCEDURE - Step 7
REMOVE NO. 1 RADIATOR GRILLE RETAINER
Refer to PROCEDURE - Step 19
REMOVE NO. 1 RADIATOR TO SUPPORT SEAL
Refer to PROCEDURE - Step 20
REMOVE HOOD LOCK NUT CAP
Refer to PROCEDURE - Step 2
REMOVE HOOD LOCK ASSEMBLY
- w/ Engine Hood Courtesy Switch:
  Refer to PROCEDURE - Step 3
- w/o Engine Hood Courtesy Switch:
  Refer to PROCEDURE - Step 10
REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
Refer to PROCEDURE - Step 12
REMOVE NO. 2 RADIATOR AIR GUIDE
Refer to PROCEDURE - Step 13
REMOVE FRONT BUMPER ENERGY ABSORBER
Refer to PROCEDURE - Step 21
REMOVE FRONT BUMPER REINFORCEMENT
Refer to PROCEDURE - Step 23
REMOVE NO. 1 RADIATOR AIR GUIDE LH
Refer to PROCEDURE - Step 32
REMOVE NO. 1 RADIATOR AIR GUIDE RH
Refer to PROCEDURE - Step 33

DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

Remove the bolt to disconnect the discharge hose sub-assembly from the cooler condenser assembly.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Remove the O-ring from the discharge hose sub-assembly.
NOTE:
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.

DISCONNECT COOLER REFRIGERANT LIQUID PIPE A (for VALEO Made)

Remove the bolt to disconnect the cooler refrigerant liquid pipe A from the cooler condenser assembly.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Remove the O-ring from the cooler refrigerant liquid pipe A.
NOTE:
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.

DISCONNECT COOLER REFRIGERANT LIQUID PIPE A (for DENSO Made)

While pressing the end of the cooler refrigerant liquid pipe A into the end of the cooler condenser assembly, use pliers to squeeze together both sides of the piping clamp until it breaks apart.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

*1	Cooler Refrigerant Liquid Pipe A	*2	Cooler Condenser Assembly
*3	Piping Clamp	-	-
*a	Press In	-	-

NOTE:

If any foreign matter is adhered to the connecting part, brush it off or use compressed air to remove it.
Make sure that fragments of the piping clamp do not enter the piping.

Disconnect the cooler refrigerant liquid pipe A.
NOTE:
Clean off any foreign matter near the ends of the cooler refrigerant liquid pipe A and cooler condenser assembly.
Remove the 2 O-rings from the cooler refrigerant liquid pipe A.
NOTE:
Wrap the open ends of the separated cooler condenser assembly and cooler refrigerant liquid pipe A with vinyl tape to prevent entry of moisture and foreign matter.
Remove the piping clamp.

REMOVE COOLER CONDENSER ASSEMBLY

Disengage the claws and guides to remove the cooler condenser assembly as shown in the illustration.

	Remove in this Direction (1)
	Remove in this Direction (2)

NOTE:

Do not damage the cooler condenser assembly or radiator assembly when removing the cooler condenser assembly.