LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2021 >> 4Runner TRD Pro >> Repair and Diagnosis >> Electrical >> Gauges >> Interior Panels / Trim - Service Information >> Roof Headlining >> Removal [08/2019 - ] >> Procedure

Removal [08/2019 - ]: Procedure

  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [08/2019 - 08/2022] , or refer to INITIALIZATION [08/2022 - ]

  2. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat) 

    Refer to REMOVAL [08/2015 - ]

  3. REMOVE DOOR SCUFF PLATE ASSEMBLY LH 
    1. Put protective tape around the door scuff plate assembly LH.
      GTY879210Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Protective Tape
    2. Using a screwdriver, detach the 4 clips, 10 claws and 2 guides to remove the door scuff plate assembly LH.

      HINT: 

      Tape the screwdriver tip before use.

  4. REMOVE DOOR SCUFF PLATE ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  5. REMOVE COWL SIDE TRIM BOARD LH 
    1. Remove the clip.
      GTY227336Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the clip and claw to remove the cowl side trim board LH.
  6. REMOVE COWL SIDE TRIM BOARD RH 

    HINT: 

    Use the same procedure as for the LH side.

  7. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH 
    1. Remove the front door opening trim weatherstrip LH.
      GTY220627Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH 

    HINT: 

    Use the same procedure as for the LH side.

  9. REMOVE ASSIST GRIP PLUG 
    1. Using a screwdriver, detach the 2 claws to remove the assist grip plug.
      GTY917755Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Protective Tape

      HINT: 

      • Tape the screwdriver tip before use.
      • Use the same procedure for the other assist grip plug.
  10. REMOVE NO. 1 ASSIST GRIP 
    1. Remove the 2 bolts.
      GTY226526Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the 2 claws to remove the No. 1 assist grip.
  11. REMOVE FRONT PILLAR GARNISH RH 
    1. Detach the clip and 3 guides to remove the front pillar garnish RH.
      GTY220631Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Protect the curtain shield airbag assembly.
      GTY929995Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Completely cover the curtain shield airbag assembly with a protective cover and secure the ends of the cover with adhesive tape as shown in the illustration.
        TEXT IN ILLUSTRATION

        *a Adhesive Tape
        *1 Curtain Shield Airbag Assembly
        *2 Protective Cover
        NOTE:

        Cover the curtain shield airbag assembly with a protective cover as soon as the front pillar garnish RH is removed.

  12. REMOVE FRONT PILLAR GARNISH LH 
    1. Using a screwdriver, detach the 2 claws to remove the No. 1 front pillar garnish cover LH.
      GTY879412Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Protective Tape

      HINT: 

      Tape the screwdriver tip before use.

    2. Remove the bolt.
      GTY442506Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Detach the clip.
    4. Detach the 2 guides to remove the front pillar garnish LH.
      GTY442503Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Protect the curtain shield airbag assembly.
      GTY928843Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Completely cover the curtain shield airbag assembly with a protective cover and secure the ends of the cover with adhesive tape as shown in the illustration.
        TEXT IN ILLUSTRATION

        *a Adhesive Tape
        *1 Curtain Shield Airbag Assembly
        *2 Protective Cover
        NOTE:

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish LH is removed.

  13. REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat) 
    1. Using a screwdriver, detach the 2 claws to remove the rear No. 1 floor step cover.
      GTY895115Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Protective Tape

      HINT: 

      • Tape the screwdriver tip before use.
      • Use the same procedure for all the rear No. 1 floor step covers.
  14. REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat) 
    1. Remove the 2 bolts and quarter scuff plate LH.
      GTY227337Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. REMOVE QUARTER SCUFF PLATE RH (w/ Rear No. 2 Seat) 

    HINT: 

    Use the same procedure as for the LH side.

  16. REMOVE REAR DOOR SCUFF PLATE LH 
    1. Put protective tape around the rear door scuff plate LH.
    2. Using a screwdriver, detach the 3 clips, 6 claws and 2 guides to remove the rear door scuff plate LH.
      GTY916717Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Protective Tape

      HINT: 

      Tape the screwdriver tip before use.

  17. REMOVE REAR DOOR SCUFF PLATE RH 

    HINT: 

    Use the same procedure as for the LH side.

  18. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH 
    1. Remove the rear door opening trim weatherstrip LH.
      GTY220626Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  19. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH 

    HINT: 

    Use the same procedure as for the LH side.

  20. REMOVE OUTER LAP BELT ANCHOR COVER 
    1. Detach the 3 claws to remove the outer lap belt anchor cover.
      GTY227335Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use the same procedure for the other outer lap belt anchor cover.

  21. REMOVE LOWER CENTER PILLAR GARNISH LH 
    1. Remove the bolt to disconnect the front seat outer belt floor anchor.
      GTY649139Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the 4 claws and 2 clips to remove the lower center pillar garnish LH.
      GTY680579Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  22. REMOVE LOWER CENTER PILLAR GARNISH RH 

    HINT: 

    Use the same procedure as for the LH side.

  23. REMOVE CENTER PILLAR GARNISH LH 
    1. Move the front shoulder belt anchor adjuster to the lowest position.
      GTY220633Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt.
    3. Detach the 2 clips and 2 guides.
    4. Pass the front seat outer belt floor anchor through the center pillar garnish LH to remove the center pillar garnish LH.
  24. REMOVE CENTER PILLAR GARNISH RH 

    HINT: 

    Use the same procedure as for the LH side.

  25. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM COVER (w/o Deck Board) 
    1. Detach the 4 claws to open the cover.
      GTY220588Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt, luggage hold belt striker and No. 1 luggage compartment trim cover.
      GTY878839Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Luggage Hold Belt Striker

      HINT: 

      Use the same procedure for the other No. 1 luggage compartment trim cover.

  26. REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Deck Board) 
    1. Detach the clip to remove the No. 1 deck board sub-assembly.
      GTY220590Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  27. REMOVE LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY LH (w/ Deck Board) 
    1. Using a screwdriver, detach the 4 clips and 2 guides to remove the luggage compartment side cover sub-assembly LH.
      GTY905274Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Protective Tape

      HINT: 

      Tape the screwdriver tip before use.

  28. REMOVE LUGGAGE COMPARTMENT SIDE COVER SUB-ASSEMBLY RH (w/ Deck Board) 

    HINT: 

    Use the same procedure as for the LH side.

  29. REMOVE DECK BOARD ASSEMBLY (w/ Deck Board) 
    1. Remove the 6 bolts.
      GTY442505Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the 2 guides to remove the deck board assembly.
  30. REMOVE NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/ Deck Board) 
    1. Detach the 2 claws to open the cover.
      GTY234057Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt, luggage hold belt striker and No. 2 luggage compartment trim cover.
      GTY894225Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Luggage Hold Belt Striker

      HINT: 

      Use the same procedure for the other No. 2 luggage compartment trim cover.

  31. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY (w/ Deck Board) 
    1. Detach the 2 clips and 2 guides to remove the No. 2 deck board sub-assembly.
      GTY234052Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  32. REMOVE REAR NO. 2 FLOOR BOARD ASSEMBLY (w/ Deck Board) 
    1. Detach the 3 clips to remove the rear No. 2 floor board assembly.
      GTY220568Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  33. REMOVE INNER FLOOR SIDE RAIL SUB-ASSEMBLY (w/ Deck Board) 
    1. Remove the 4 bolts and inner floor side rail sub-assembly.
      GTY442504Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  34. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE 
    1. Detach the 5 clips to remove the rear floor mat rear support plate.
      GTY234056Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  35. REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Deck Board) 
    1. Detach the 4 claws to remove the rear floor carpet assembly.
      GTY220589Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  36. REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER 
    1. Detach the 3 claws to remove the rear No. 1 seat outer lap belt anchor cover.
      GTY220598Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use the same procedure for the other rear No. 1 seat outer lap belt anchor cover.

  37. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK 
    1. Remove the No. 1 luggage compartment trim hook by turning it clockwise.
      GTY240898Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use the same procedure for the other No. 1 luggage compartment trim hook.

  38. REMOVE FRONT DECK SIDE TRIM COVER LH 
    1. Using a screwdriver, detach the 2 claws to remove the front deck side trim cover LH.
      GTY921074Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Protective Tape

      HINT: 

      Tape the screwdriver tip before use.

  39. REMOVE FRONT DECK SIDE TRIM COVER RH 

    HINT: 

    Use the same procedure as for the LH side.

  40. REMOVE NO. 2 LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat) 
    1. Detach the 2 claws to open the cover.
      GTY234057Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the bolt, luggage hold belt striker and No. 2 luggage compartment trim cover.
      GTY894223Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *1 Luggage Hold Belt Striker

      HINT: 

      Use the same procedure for the other No. 2 luggage compartment trim cover.

  41. REMOVE REAR SEATBACK LOCK CONTROL LEVER BASE LH (w/o Rear No. 2 Seat) 

    Refer to PROCEDURE - Step 9

  42. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH 
    1. w/o Rear No. 2 Seat:
      1. Remove the bolt to disconnect the rear No. 1 seat outer belt floor anchor.
        GTY686833Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Remove the 5 bolts and 2 screws.
      3. Detach the 7 clips, 5 claws and 2 guides.
        GTY1151197Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. w/ Rear No. 2 Seat:
      1. Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.
        GTY686833Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Remove the bolt to disconnect the rear No. 2 seat outer belt floor anchor.
        GTY220599Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Remove the 3 bolts and 2 screws.
      4. Detach the 7 clips, 5 claws and 2 guides to remove the deck trim side panel assembly LH.
        GTY730961Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  43. REMOVE REAR SEATBACK LOCK CONTROL LEVER BASE RH (w/o Rear No. 2 Seat) 

    Refer to PROCEDURE - Step 9

  44. REMOVE DECK TRIM SIDE PANEL ASSEMBLY RH 
    1. w/o Rear No. 2 Seat:
      1. Remove the bolt to disconnect the rear No. 1 seat outer belt floor anchor.
        GTY293853Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Remove the 5 bolts and screw.
      3. Detach the 7 clips, 5 claws and 2 guides.
        GTY1140325Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      4. Disconnect each connector.
    2. w/ Rear No. 2 Seat:
      1. Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.
        GTY293853Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.
        GTY672600Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      3. Remove the 3 bolts and screw.
      4. Detach the 7 clips, 5 claws and 2 guides.
      5. Disconnect each connector and remove the deck trim side panel assembly RH.
        GTY234059Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  45. REMOVE REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY LH 
    1. w/o Rear No. 2 Seat:
      GTY220634Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Detach the 6 clips and guide to remove the rear No. 2 window side garnish assembly LH.
    2. w/ Rear No. 2 Seat:
      GTY225985Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Detach the 6 clips and guide.
      2. Detach the 7 claws and guide and pass the rear No. 2 seat outer belt floor anchor through the rear No. 2 window side garnish assembly LH to remove the rear No. 2 window side garnish assembly LH.
        GTY220632Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  46. REMOVE REAR NO. 2 WINDOW SIDE GARNISH ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  47. REMOVE REAR WINDOW SIDE GARNISH ASSEMBLY LH 
    1. Detach the 7 clips and 4 guides.
      GTY220600Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the 4 claws and 2 guides and pass the rear No. 1 seat outer belt floor anchor through the rear window side garnish assembly LH to remove the rear window side garnish assembly LH.
      GTY220601Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  48. REMOVE REAR WINDOW SIDE GARNISH ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  49. REMOVE ASSIST GRIP SUB-ASSEMBLY 
    1. Using a clip remover, detach the 4 claws.
      GTY903800Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Protective Tape
      *1 Assist Grip Plug
      NOTE:

      Do not forcibly pry the assist grip plugs to prevent them from being deformed.

      HINT: 

      • Gently pry the assist grip plugs as shown in the illustration to detach the claws.
      • Tape the clip remover tip before use.
      • Use the same procedure for the other assist grip sub-assembly.
    2. Pull off the 2 assist grip plugs by hand.
    3. Detach the 2 clips to remove the assist grip sub-assembly.
      GTY842675Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the 2 clips from the vehicle body.
  50. REMOVE REAR ASSIST GRIP ASSEMBLY 
    1. Using a clip remover, detach the 4 claws.
      GTY944269Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Protective Tape
      *1 Assist Grip Plug
      NOTE:

      Do not forcibly pry the assist grip plugs to prevent them from being deformed.

      HINT: 

      • Gently pry the rear assist grip plugs as shown in the illustration to detach the claws.
      • Tape the clip remover tip before use.
      • Use the same procedure for the other rear assist grip assembly.
    2. Pull off the 2 assist grip plugs by hand.
    3. Detach the 2 clips to remove the rear assist grip assembly.
      GTY842676Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Remove the 2 clips from the vehicle body.
  51. REMOVE COAT HOOK 
    1. Using a screwdriver, detach the claw to open the cover.
      GTY906525Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      TEXT IN ILLUSTRATION

      *a Protective Tape
    2. Remove the screw and coat hook.
      GTY220602Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use the same procedure for the other coat hook.

  52. REMOVE VISOR BRACKET COVER LH 
    1. Detach the 4 claws to remove the visor bracket cover LH.
      GTY228375Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  53. REMOVE VISOR BRACKET COVER RH 

    HINT: 

    Use the same procedure as for the LH side.

  54. REMOVE VISOR ASSEMBLY LH 
    1. Remove the 2 screws and visor assembly LH.
      GTY228377Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  55. REMOVE VISOR ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  56. REMOVE VISOR HOLDER 
    1. Turn the visor holder approximately 45° to pull it out as shown in the illustration.
      GTY727842Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the 2 claws to remove the visor holder.

      HINT: 

      Use the same procedure for the other visor holder.

  57. REMOVE DRIVE MONITOR SWITCH (w/ Drive Monitor Switch) 

    Refer to PROCEDURE - Step 1

  58. REMOVE MAP LIGHT ASSEMBLY 

    Refer to PROCEDURE - Step 2

  59. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER 

    Refer to PROCEDURE - Step 1

  60. REMOVE NO. 1 FORWARD RECOGNITION COVER 

    Refer to PROCEDURE - Step 1

  61. REMOVE NO. 1 ROOM LIGHT ASSEMBLY 

    Refer to PROCEDURE - Step 1

  62. REMOVE ROOF HEADLINING ASSEMBLY 

    HINT: 

    Before removing the roof headlining assembly, move the front seats and rear No. 1 seat to the positions shown in the illustration.

    GTY686880Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Disconnect the forward recognition camera connector and camera heater connector.
      GTY919302Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the inner rear view mirror assembly connector.
      GTY846864Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. w/ Sliding Roof:

      Disconnect the sliding roof drive gear connector.

      GTY234062Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Disconnect the 2 connectors and detach the 3 clamps from the front pillar LH.
      GTY923442Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Remove the bolt.
      GTY919301Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Disconnect the 2 connectors and detach the 2 clamps from the front pillar RH.
    7. Disconnect the connector and detach the clamp from the rear pillar RH.
      GTY220606Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Detach the guide and remove the bolt.
      GTY919875Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    9. Disconnect the 3 connectors and detach the clamp.
      GTY919874Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    10. w/o Sliding Roof:
      GTY847145Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Remove the 5 clips.
    11. w/ Sliding Roof:
      GTY859471Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Remove the 5 clips.
      2. Detach the 2 guides and 8 fasteners.
        TEXT IN ILLUSTRATION

        *1 Guide
        *2 Fastener
    12. Remove the roof headlining assembly from the back door as shown in the illustration.
      GTY220610Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:

      Be careful not to damage the roof headlining assembly when remove it.

  63. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH 
    1. Detach the 4 claws of the front shoulder belt anchor plate sub-assembly LH to slide the front shoulder belt anchor plate sub-assembly LH and remove it.
      GTY220582Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  64. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  65. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH 
    1. Detach the 3 clips to remove the roof side rail garnish assembly LH.
      GTY220570Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  66. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  67. REMOVE REAR NO. 3 SIDE RAIL SPACER LH 
    1. Detach the 2 claws to remove the rear No. 3 side rail spacer LH.
      GTY220573Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  68. REMOVE REAR NO. 3 SIDE RAIL SPACER RH 

    HINT: 

    Use the same procedure as for the LH side.

  69. REMOVE QUARTER TRIM COVER 
    1. Detach the 2 claws to remove the quarter trim cover.
      GTY220564Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      HINT: 

      Use the same procedure for the other quarter trim cover.

  70. REMOVE QUARTER TRIM JACK COVER SUB-ASSEMBLY 
    1. Detach the 3 claws and 2 guides to remove the quarter trim jack cover sub-assembly.
      GTY220579Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  71. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH 
    1. Detach the 2 claws and 2 guides to remove the rear combination light service cover LH.
      GTY220565Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  72. REMOVE REAR COMBINATION LIGHT SERVICE COVER RH 

    HINT: 

    Use the same procedure as for the LH side.

  73. REMOVE SIDE TRIM BOX LH (w/o Rear No. 2 Seat) 
    1. Remove the 2 screws.
      GTY234050Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the 8 claws to remove the side trim box LH.
  74. REMOVE SIDE TRIM BOX RH (w/o Rear No. 2 Seat) 

    HINT: 

    Use the same procedure as for the LH side.

  75. REMOVE REAR FLOOR FINISH SIDE PLATE LH (w/o Rear No. 2 Seat) 
    1. Remove the 2 screws.
      GTY234055Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the claw and 2 guides to remove the rear floor finish side plate LH.
  76. REMOVE REAR FLOOR FINISH SIDE PLATE RH (w/o Rear No. 2 Seat) 

    HINT: 

    Use the same procedure as for the LH side.

  77. REMOVE REAR SEAT SHOULDER BELT HANGER LH (w/ Rear No. 2 Seat) 
    GTY227362Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Detach the claw and guide to remove the rear seat shoulder belt hanger LH.
  78. REMOVE REAR SEAT SHOULDER BELT HANGER RH (w/ Rear No. 2 Seat) 

    HINT: 

    Use the same procedure as for the LH side.

  79. REMOVE QUARTER TRIM LID SUB-ASSEMBLY RH (w/ Rear No. 2 Seat) 
    GTY220577Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Detach the 4 claws and 2 guides to remove the quarter trim lid sub-assembly RH.
  80. REMOVE DECK SIDE TRIM CUP HOLDER LH (w/ Rear No. 2 Seat) 
    1. Remove the 4 screws.
      GTY220576Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Detach the 2 claws to remove the deck side trim cup holder LH.
  81. REMOVE DECK SIDE TRIM CUP HOLDER RH (w/ Rear No. 2 Seat) 

    HINT: 

    Use the same procedure as for the LH side.

scientia non olet · About LEMON Manuals