Installation [11/2018 - 08/2020]: Procedure

INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Check that the ignition switch is off.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

WARNING:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Attach the hook and claw to install the lower No. 1 instrument panel air bag assembly.

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Install in this Direction

Install the 2 bolts.

Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Connect the airbag connector and push the lock button to lock.

*a	Lock Button
	Push in this Direction

NOTE:

When connecting any airbag connector, take care not to damage the airbag wire harness.
Make sure the lock button is securely locked.

Check that there is no looseness in the lower No. 1 instrument panel airbag assembly.

INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
Refer to PROCEDURE - Step 19
INSTALL CONSOLE BOX ASSEMBLY
Refer to INSTALLATION [11/2018 - 12/2021]
INSTALL FUSE BOX OPENING COVER
Refer to PROCEDURE - Step 20
INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Refer to PROCEDURE - Step 25
INSTALL COWL SIDE TRIM BOARD LH
Refer to PROCEDURE - Step 41 [11/2018 - 02/2019] , or refer to PROCEDURE - Step 42 [02/2019 - 08/2020]
INSTALL FRONT DOOR SCUFF PLATE LH
Refer to PROCEDURE - Step 43 [11/2018 - 02/2019] , or refer to PROCEDURE - Step 44 [02/2019 - 08/2020]
CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
- for A25A-FKS:
  Refer to PROCEDURE - Step 2
- for A25A-FXS:
  Refer to PROCEDURE - Step 2
NOTE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Refer to INITIALIZATION [11/2018 - 02/2019] , or refer to INITIALIZATION [02/2019 - 10/2019] , or refer to INITIALIZATION [10/2019 - 06/2020] , or refer to INITIALIZATION [06/2020 - 08/2020]
INSTALL BATTERY HOLE COVER (for HV Model)
Refer to PROCEDURE - Step 3
INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)
Refer to PROCEDURE - Step 4
INSTALL DECK BOARD ASSEMBLY (for HV Model)
Refer to PROCEDURE - Step 5
PERFORM DIAGNOSTIC SYSTEM CHECK
- w/ Occupant Classification System:
  Refer to DTC CHECK / CLEAR [11/2018 - 08/2020]
- w/o Occupant Classification System:
  Refer to DTC CHECK / CLEAR [11/2018 - 08/2020]
CHECK SRS WARNING LIGHT
- w/ Occupant Classification System:
  Refer to OPERATION CHECK [11/2018 - 02/2019] , or refer to OPERATION CHECK [02/2019 - 08/2020]
- w/o Occupant Classification System:
  Refer to OPERATION CHECK [11/2018 - 08/2020]
PERFORM SYSTEM INITIALIZATION AND CALIBRATION
Refer to CAUTION / NOTICE / HINT [11/2018 - 02/2019] , or refer to CAUTION / NOTICE / HINT [02/2019 - 10/2019] , or refer to REMOVAL [10/2019 - 08/2020]