LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2019 >> Highlander Limited, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 2 (Automatic Transmission (U760E) - Service Information (1 Of 2)) >> Park / Neutral Position Switch >> Installation [12/2013 - ] >> Procedure

Installation [12/2013 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY 
    1. Move the shift lever to N.
    2. Align the protrusions of the park/neutral position switch assembly.
      GTY429638Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Protrusion
    3. Install the park/neutral position switch assembly to the manual valve lever shaft sub-assembly with the 2 bolts.

      Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

      NOTE:
      • Before installing the park/neutral position switch assembly, remove any dirt or rust on the installation portion of the manual valve lever shaft sub-assembly. Be sure to install the park/neutral position switch assembly straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.
      • After installing the park/neutral position switch assembly, confirm that the 2 protrusions on the park/neutral position switch assembly are aligned.
    4. Install the transmission control shaft lever to the manual valve lever shaft sub-assembly with the nut and washer.

      Torque: 12.7 N*m (130 kgf*cm, 9 ft.*lbf) 

    5. Connect the connector to the park/neutral position switch.
  2. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY 
    1. Install a new clip to the No. 1 transmission control cable bracket.
    2. Install the transmission control cable assembly to the No. 1 transmission control cable bracket.
      GTY432378Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Claw A
      *b Claw B
      *c Transmission Control Cable Assembly
      NOTE:
      • Make sure that the claws A on the clip are securely fit into the No. 1 transmission control cable bracket holes.
      • Make sure that the transmission control cable assembly is securely installed inside of the claws B of the clip.
    3. Install the transmission control cable assembly to the transmission control shaft lever with the nut.

      Torque: 12 N*m (122 kgf*cm, 9 ft.*lbf) 

      NOTE:

      Before connecting the transmission control cable assembly, check that the park/neutral position switch assembly and the shift lever are in neutral.

    4. Engage wire harness clamp to the wire harness clamp bracket.
  3. INSTALL AIR CLEANER CASE SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 49 , or refer to PROCEDURE - Step 49

  4. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 50 , or refer to PROCEDURE - Step 50

  5. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE 

    Refer to PROCEDURE - Step 4

  6. INSTALL INLET AIR CLEANER ASSEMBLY 

    Refer to PROCEDURE - Step 52 , or refer to PROCEDURE - Step 52

  7. INSTALL COOL AIR INTAKE DUCT SEAL 

    Refer to PROCEDURE - Step 4 , or refer to PROCEDURE - Step 4

  8. INSTALL RADIATOR SIDE SEAL RH 

    Refer to PROCEDURE - Step 5 , or refer to PROCEDURE - Step 5

  9. INSTALL RADIATOR SIDE DEFLECTOR SEAL LH 

    Refer to PROCEDURE - Step 6 , or refer to PROCEDURE - Step 6

  10. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY OPERATION 

    See step  1

  11. INSPECT SHIFT LEVER POSITION 

    See step  1

  12. ADJUST SHIFT LEVER POSITION 

    Refer to ADJUSTMENT [12/2013 - ] 

scientia non olet · About LEMON Manuals