LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2018 >> Camry LE >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 29 (Fuel System (2GR-FKS) - Service Information (Except Hybrid)) >> Fuel Pump Ecu >> Installation [06/2017 - 09/2019] >> Procedure

Installation [06/2017 - 09/2019]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. INSTALL FUEL PUMP CONTROL ECU BRACKET 
    1. Install the fuel pump control ECU bracket to the fuel pump control ECU with the 2 bolts.

      Torque: 4.5 N*m (46 kgf*cm, 40 in.*lbf) 

  2. INSTALL FUEL PUMP CONTROL ECU 
    1. Install the fuel pump control ECU to the vehicle body with the nut.

      Torque: 8.0 N*m (82 kgf*cm, 71 in.*lbf) 

    2. Connect the 2 fuel pump control ECU connectors.
  3. INSTALL ROOM PARTITION BOARD LH 

    Refer to PROCEDURE - Step 4

  4. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY 

    Refer to PROCEDURE - Step 5

  5. INSTALL REAR SEAT SHOULDER BELT HOLE COVER 

    Refer to PROCEDURE - Step 6

  6. INSTALL INNER ROOF SIDE GARNISH LH 

    Refer to PROCEDURE - Step 21 [06/2017 - 08/2018] , or refer to PROCEDURE - Step 21 [08/2018 - 09/2019]

  7. INSTALL INNER ROOF SIDE GARNISH RH 

    HINT: 

    Use the same procedure as for the LH side.

  8. CONNECT REAR SEAT OUTER BELT ASSEMBLY LH 

    Refer to PROCEDURE - Step 8

  9. CONNECT REAR SEAT OUTER BELT ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  10. INSTALL CENTER STOP LIGHT SET 

    Refer to PROCEDURE - Step 1

  11. INSTALL REAR SIDE SEATBACK ASSEMBLY LH 

    Refer to PROCEDURE - Step 1

  12. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH 

    Refer to PROCEDURE - Step 1

  13. INSTALL REAR SIDE SEATBACK ASSEMBLY RH 

    HINT: 

    Use the same procedure as for the LH side.

  14. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH 

    HINT: 

    Use the same procedure as for the LH side.

  15. INSTALL REAR SEATBACK ASSEMBLY LH 

    Refer to PROCEDURE - Step 5

  16. INSTALL REAR SEAT CUSHION LOCK HOOK 

    Refer to PROCEDURE - Step 7

  17. INSTALL REAR SEAT CUSHION ASSEMBLY 

    for TMC Made:

    Refer to PROCEDURE - Step 11

    for TMMK Made:

    Refer to PROCEDURE - Step 8

  18. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for TMC Made) 

    Refer to PROCEDURE - Step 12

  19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [06/2017 - 08/2018] , or refer to INITIALIZATION [08/2018 - 09/2019]

  20. PERFORM DIAGNOSTIC SYSTEM CHECK 

    Refer to DTC CHECK / CLEAR [03/2017 - ]

  21. INSPECT SRS WARNING LIGHT 

    Refer to OPERATION CHECK [06/2017 - 09/2019]

scientia non olet · About LEMON Manuals