LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2016 >> Prius Four >> Repair and Diagnosis >> Hybrid/Electric Powertrain >> Testing and Diagnosis >> Hybrid Control System (Nickel Metal Hydride) - Diagnostic Codes (6 Of 8) >> HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY) >> DTC P3107-15: Lost Communication with Airbag System Control Module Circuit Short to Auxiliary Battery or Open [08/2019 -] >> Procedure

DTC P3107-15: Lost Communication with Airbag System Control Module Circuit Short to Auxiliary Battery or Open [08/2019 -]: Procedure

  1. CHECK DTC OUTPUT (SRS AIRBAG) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.
    4. Check for DTCs.

      Body Electrical > SRS Airbag > Trouble Codes 

      Result

      Result  Proceed to
      DTCs are not output A
      DTCs are output B
    5. Turn the power switch off.

    Result: 

    B 

    GO TO DTC CHART (AIRBAG SYSTEM). Refer to  DIAGNOSTIC TROUBLE CODE CHART [08/2019 - 07/2020]  , or refer to  DIAGNOSTIC TROUBLE CODE CHART [07/2020 -] 

    Result: 

    A 

    See step  2

  2. CHECK AIRBAG ECU ASSEMBLY (CHECK WAVEFORM) 

    See step  2

    Result

    Result  Proceed to
    The waveform appears as shown in the illustration. A
    The waveform differs from the one shown in the illustration. B

    Result: 

    B 

    See step  6

    Result: 

    A 

    See step  3

  3. CLEAR DTC 

    Refer to PROCEDURE - Step 3

    Result

    Proceed to
    NEXT

    Result: 

    NEXT 

    See step  4

  4. CHECK DTC OUTPUT (HYBRID CONTROL) 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
    4. Check for DTCs.

      Powertrain > Hybrid Control > Trouble Codes 

      Result

      Result  Proceed to
      P3107-15 is not output A
      P3107-15 is output B
    5. Turn the power switch off.

    Result: 

    B 

    REPLACE HYBRID VEHICLE CONTROL ECU. Refer to  REMOVAL [08/2019 - 07/2020]  , or refer to  REMOVAL [07/2020 -] 

    Result: 

    A 

    See step  5

  5. CHECK FOR INTERMITTENT PROBLEMS 

    HINT: 

    Refer to CHECK FOR INTERMITTENT PROBLEMS [11/2015 -]

    Result

    Proceed to
    OK
    NG

    Result: 

    OK 

    REPLACE HYBRID VEHICLE CONTROL ECU. Refer to  REMOVAL [08/2019 - 07/2020]  , or refer to  REMOVAL [07/2020 -] 

    Result: 

    NG 

    REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA 

  6. CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR) 

    Refer to PROCEDURE - Step 1

    Result

    Proceed to
    OK
    NG

    Result: 

    NG 

    CONNECT SECURELY 

    Result: 

    OK 

    See step  7

  7. CHECK CONNECTOR CONNECTION CONDITION (AIRBAG ECU ASSEMBLY CONNECTOR) 
    1. Check the connector connections and contact pressure of the relevant terminals for the F122 airbag ECU assembly connector.
      GTY900965Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Airbag ECU Assembly)

      OK

      The connectors are connected securely and there are no contact pressure problems.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    CONNECT SECURELY 

    Result: 

    OK 

    See step  8

  8. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AIRBAG ECU ASSEMBLY) 
    1. Disconnect the F3 hybrid vehicle control ECU connector.
    2. Disconnect the F122 airbag ECU assembly connector.
    3. Turn the power switch on (IG).
    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      (F3)

      (F3)

      Tester Connection Condition Specified Condition
      F3-29 (ABFS) - Body ground Power switch on (IG) Below 1 V
      GTY845458Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Front view of wire harness connector
      (to Hybrid Vehicle Control ECU)
      *b Front view of wire harness connector
      (to Airbag ECU Assembly)
      NOTE:

      Turning the power switch on (IG) with the airbag ECU assembly connector and the hybrid vehicle control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    5. Turn the power switch off.
    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)

      (F3, F122)

      (F3)

      (F122)

      Tester Connection Condition Specified Condition
      F3-29 (ABFS) - F122-24 (GSW2) Power switch off Below 1 Ω

      Standard Resistance (Check for Short)

      (F3, F122)

      (F3)

      (F122)

      Tester Connection Condition Specified Condition
      F3-29 (ABFS) or F122-24 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher
    7. Reconnect the F122 airbag ECU assembly connector.
    8. Reconnect the F3 hybrid vehicle control ECU connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    NG 

    REPAIR OR REPLACE HARNESS OR CONNECTOR 

    Result: 

    OK 

    See step  9

  9. CHECK HYBRID VEHICLE CONTROL ECU 
    1. Disconnect the F122 airbag ECU assembly connector.
    2. Turn the power switch on (IG).
    3. Measure the voltage according to the value(s) in the table below.
      GTY887340Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Component with harness connected
      (Hybrid Vehicle Control ECU)      		 - -
      NOTE:

      Turning the power switch on (IG) with the airbag ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

      Standard Voltage

      (F3)

      (F3)

      Tester Connection Condition Specified Condition
      F3-29 (ABFS) - Body ground Power switch on (IG) 11 to 14 V
    4. Turn the power switch off.
    5. Reconnect the F122 airbag ECU assembly connector.

      Result

      Proceed to
      OK
      NG

    Result: 

    OK 

    REPLACE AIRBAG ECU ASSEMBLY. Refer to  REMOVAL [08/2019 - 07/2020]  , or refer to  REMOVAL [07/2020 -] 

    Result: 

    NG 

    REPLACE HYBRID VEHICLE CONTROL ECU. Refer to  REMOVAL [08/2019 - 07/2020]  , or refer to  REMOVAL [07/2020 -] 

scientia non olet · About LEMON Manuals