LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2016 >> Highlander Limited, FWD >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 70 (Supplemental Restraint System (Service Information) (Hybrid)) >> Side Airbag Sensor >> Installation [02/2014 - ] >> Procedure

Installation [02/2014 - ]: Procedure

WARNING: This page is about a different variant/trim than selected.
  1. INSTALL DOOR SIDE AIRBAG SENSOR 
    1. Check that the power switch is off.
    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
      WARNING:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.
      GTY454543Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *a Incorrect *b Correct
    4. Insert the door side airbag sensor pin (stopper) into the door hole and install the door side airbag sensor to the front door panel with the bolt.

      Torque: 9.0 N*m (92 kgf*cm, 80 in.*lbf) 

      NOTE:
      • If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
      • When installing the door side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
      • Make sure that the door side airbag sensor pin (stopper) is securely inserted into the door hole.
      • Tighten the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.
    5. Connect the connector to the door side airbag sensor.
      NOTE:

      When connecting any airbag connector, take care not to damage the airbag wire harness.

      1. Be sure to engage the connector until it is locked (when locking, make sure that a click sound can be heard).
        GTY424108Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        *a White Housing Lock *b Connection is completed

        HINT: 

        When engaged, the white housing lock will slide. Be sure not to hold the white housing lock or part (A), as it may result in an insecure fit.

    6. Check that there is no looseness in the installed parts of the door side airbag sensor.
  2. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 42 , or refer to PROCEDURE - Step 42 , or refer to PROCEDURE - Step 42

  3. INSTALL COURTESY LIGHT ASSEMBLY 

    Refer to PROCEDURE - Step 2

  4. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side) 

    Refer to PROCEDURE - Step 44 , or refer to PROCEDURE - Step 44 , or refer to PROCEDURE - Step 44

  5. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side) 

    Refer to PROCEDURE - Step 45 , or refer to PROCEDURE - Step 45 , or refer to PROCEDURE - Step 45

  6. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG 

    Refer to PROCEDURE - Step 46 , or refer to PROCEDURE - Step 46 , or refer to PROCEDURE - Step 46

  7. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH 

    Refer to PROCEDURE - Step 47 , or refer to PROCEDURE - Step 47 , or refer to PROCEDURE - Step 47

  8. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL 
    NOTE:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Refer to INITIALIZATION [02/2014 - 11/2016] , or refer to INITIALIZATION [11/2016 - ]

  9. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 71 , or refer to PROCEDURE - Step 72 , or refer to PROCEDURE - Step 70

  10. INSTALL DECK BOARD ASSEMBLY 

    Refer to PROCEDURE - Step 72 , or refer to PROCEDURE - Step 73 , or refer to PROCEDURE - Step 71

  11. PERFORM DIAGNOSTIC SYSTEM CHECK 

    Refer to DTC CHECK / CLEAR [02/2014 - ]

  12. INSPECT SRS WARNING LIGHT 

    Refer to DIAGNOSIS SYSTEM [02/2014 - ]

scientia non olet · About LEMON Manuals