Installation [11/2016 - ]: Procedure

1. Install the brake master cylinder sub-assembly, brake stroke simulator cylinder with bracket and 2 new brake master cylinder gaskets to the brake master cylinder bracket as shown in the illustration.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   *1	Brake Master Cylinder Sub-assembly	*2	Brake Stroke Simulator Cylinder with Bracket
   *3	Brake Master Cylinder Gasket	*4	Brake Master Cylinder Bracket

2. Install the 2 nuts to secure them.

   Torque: 12.5 N*m (127 kgf*cm, 9 ft.*lbf) 

1. Using a union nut wrench, install the brake stroke simulator tube to the brake master cylinder sub-assembly and brake stroke simulator cylinder sub-assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Torque: 15.2 N*m (155 kgf*cm, 11 ft.*lbf) 

   NOTE:

   • Do not kink or damage the brake stroke simulator tube.
   • Do not allow any foreign matter such as dirt or dust to enter the brake stroke simulator tube from the connecting parts.
   • Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

     Refer to PRECAUTION [11/2016 - ]

1. Install a new brake master cylinder gasket to the brake master with stroke simulator cylinder assembly.

1. Install the brake master with stroke simulator cylinder assembly with the 4 nuts.

   Torque: 12.7 N*m (130 kgf*cm, 9 ft.*lbf) 

   NOTE:

   Do not kink or damage the brake lines.

2. Connect the connector to the brake stroke simulator cylinder sub-assembly.

See step  3

See step  4

1. Using a union nut wrench, connect the front No. 7 brake tube to the brake stroke simulator cylinder sub-assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Torque: 15.2 N*m (155 kgf*cm, 11 ft.*lbf) 

   NOTE:

   • Do not kink or damage the front No. 7 brake tube.
   • Do not allow the front No. 7 brake tube to twist or interfere with other parts or the vehicle body during tightening.
   • Do not allow any foreign matter such as dirt or dust to enter the front No. 7 brake tube from the connecting parts.
   • Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

     Refer to PRECAUTION [11/2016 - ]

1. Using a union nut wrench, connect the front No. 6 brake tube to the brake master cylinder sub-assembly.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Torque: 15.2 N*m (155 kgf*cm, 11 ft.*lbf) 

   NOTE:

   • Do not kink or damage the front No. 6 brake tube.
   • Do not allow the front No. 6 brake tube to twist or interfere with other parts or the vehicle body during tightening.
   • Do not allow any foreign matter such as dirt or dust to enter the front No. 6 brake tube from the connecting parts.
   • Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

     Refer to PRECAUTION [11/2016 - ]

1. Connect the No. 2 reservoir hose to the brake master cylinder sub-assembly, and slide the clip to secure it.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Connect the No. 1 reservoir hose to the brake master cylinder sub-assembly, and slide the clip to secure it.

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Refer to PROCEDURE - Step 3

Refer to PROCEDURE - Step 6

Refer to PROCEDURE - Step 4

Refer to PROCEDURE - Step 5

Refer to PROCEDURE - Step 6

Refer to PROCEDURE - Step 10

Refer to PROCEDURE - Step 3

Refer to PROCEDURE - Step 4

Refer to BLEEDING [02/2014 - ] 

Refer to ADJUSTMENT [02/2014 - ] 

Refer to ON-VEHICLE INSPECTION [02/2014 - ] 

Refer to TEST MODE PROCEDURE [11/2016 - ]