LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2015 >> Highlander LE Plus, AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 61 (Engine Control System (2GR-FXS) - Service Information - (Hybrid)) >> Throttle Body >> Removal [11/2016 - ] >> Procedure

Removal [11/2016 - ]: Procedure

WARNING: This page is about a different car, the 2019 Toyota Highlander, 2018 Toyota Highlander, and 2017 Toyota Highlander. However, it is still accessible from the selected car via links, so may be relevant.
  1. REMOVE RADIATOR SIDE DEFLECTOR SEAL LH 

    Refer to PROCEDURE - Step 1

  2. REMOVE RADIATOR SIDE SEAL RH 

    Refer to PROCEDURE - Step 2

  3. REMOVE COOL AIR INTAKE DUCT SEAL 

    Refer to PROCEDURE - Step 3

  4. DRAIN ENGINE COOLANT (for Engine) 

    Refer to PROCEDURE - Step 1

  5. REMOVE INLET AIR CLEANER ASSEMBLY 
    1. Disengage the 3 inverter drain hose clamps from the inlet air cleaner assembly.
      GTY692615Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Remove the 3 bolts and inlet air cleaner assembly from the air cleaner assembly with air cleaner hose.
      GTY692616Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY 

    Refer to REMOVAL [02/2014 - ]

  7. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY 

    Refer to PROCEDURE - Step 3

  8. REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE 
    1. Remove the 2 bolts from the air cleaner assembly with air cleaner hose.
      GTY732248Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disconnect the mass air flow meter sub-assembly connector.
      GTY686473Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Air Cleaner Assembly with Air Cleaner Hose
      *a Wire Harness Clamp
      *b Grommet
    3. Disengage the wire harness clamp and grommet to separate the air cleaner assembly with air cleaner hose.
    4. Slide the clip and disconnect the No. 2 ventilation hose from the air cleaner assembly with air cleaner hose.
      GTY704930Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 Fuel Vapor Feed Hose Assembly
      *2 No. 2 Ventilation Hose
    5. Disengage the fuel vapor feed hose assembly from the air cleaner assembly with air cleaner hose.
    6. Loosen the hose clamp and remove the air cleaner assembly with air cleaner hose from the throttle body with motor assembly.
      GTY692609Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  9. REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY 
    1. Slide the 2 clips and disconnect the No. 2 water by-pass hose and No. 3 water by-pass hose from the throttle body with motor assembly.
      GTY716721Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      *1 No. 2 Water By-pass Hose
      *2 No. 3 Water By-pass Hose
    2. Disconnect the throttle body with motor assembly connector.
      GTY692611Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    3. Remove the 4 bolts and throttle body with motor assembly from the intake air surge tank assembly.
      NOTE:

      If the throttle body with motor assembly has been struck or dropped, replace it.

  10. REMOVE THROTTLE BODY GASKET 
    1. Remove the throttle body gasket from the intake air surge tank assembly.
      GTY692612Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals