LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2011 >> Highlander Hybrid Limited >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 42 (Engine Control System (1AR-FE) (Diagnostic Codes (P1604 - U0101) & Circuit Tests)) >> SFI System >> DTC P2A00: A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) >> Procedure

DTC P2A00: A/F Sensor Circuit Slow Response (Bank 1 Sensor 1): Procedure

WARNING: This page is about a different variant/trim than selected.
  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00) 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine / Trouble Codes.
    5. Read the DTCs.

      Result

      Result Proceed to
      DTC P2A00 is output A
      DTC P2A00 and other DTCs are output B

      HINT: 

      If any DTCs other than P2A00 are output, troubleshoot those DTCs first.

    B → See step   9 

    A: Go to next step 

  2. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE). Refer to  PROCEDURE - Step 1 

    NG → See step   10 

    OK: Go to next step 

  3. CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) See step   1 

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK: Go to next step 

  4. PERFORM CONFIRMATION DRIVING PATTERN 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Clear the DTCs, refer to DTC CHECK / CLEAR .
    5. Turn the ignition switch off.
    6. Turn the ignition switch to ON and turn the Techstream on.
    7. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    NEXT: Go to next step 

  5. CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00) 
    1. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
    2. Input the DTC: P2A00.
    3. Check the DTC judgment.

      Result

      Result Proceed to
      ABNORMAL (DTC P2A00 is output) A
      NORMAL (DTC is not output) B

    B → See step   11 

    A: Go to next step 

  6. REPLACE AIR FUEL RATIO SENSOR 
    1. Replace the air fuel ratio sensor, refer to REMOVAL .

    NEXT: Go to next step 

  7. PERFORM CONFIRMATION DRIVING PATTERN 
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Clear the DTCs, refer to DTC CHECK / CLEAR .
    5. Turn the ignition switch off.
    6. Turn the ignition switch to ON and turn the Techstream on.
    7. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    NEXT: Go to next step 

  8. CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00) 
    1. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
    2. Input the DTC: P2A00.
    3. Check the DTC judgment.

      Result

      Result Proceed to
      ABNORMAL (DTC P2A00 is output) A
      NORMAL (DTC is not output) B

    B → END 

    A → See step   12 

  9. GO TO DTC CHART. Refer to  DIAGNOSTIC TROUBLE CODE CHART 
  10. REPLACE AIR FUEL RATIO SENSOR. Refer to  REMOVAL 
  11. CHECK FOR INTERMITTENT PROBLEMS. Refer to  CHECK FOR INTERMITTENT PROBLEMS 
  12. CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO. Refer to  INSPECTION PROCEDURE 
scientia non olet · About LEMON Manuals