Front Seat Outer Belt Assembly With PRETENSIONER: Installation

INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY
1. Engage the adjuster positioning hole with the claw and install the front shoulder belt anchor adjuster assembly with the 2 bolts.
  Torque: 41 N*m (420 kgf*cm, 30 ft.*lbf)
  
  Fig 1: Identifying Front Shoulder Belt Anchor Adjuster Assembly Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT SEAT OUTER BELT ASSEMBLY
1. Install the front seat outer belt assembly with the 2 bolts.
  Torque: Bolt <A>
  
  4.9 N*m (50 kgf*cm, 43 in.*lbf)
  
  Bolt <B>
  
  41 N*m (420 kgf*cm, 30 ft.*lbf)
  
  Fig 2: Identifying Front Seat Outer Belt Assembly With Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. for Front Passenger Side:
  1. Engage the clamp.
  Fig 3: Identifying Front Seat Outer Belt Assembly Connector Clamp
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Connect the connector and lock the locking button as shown in the illustration.
  NOTE: Securely lock the locking button.
  
  Fig 4: Connecting Connector And Lock Locking Button
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Connect the shoulder anchor of the front seat outer belt assembly with the nut.
  Torque: 41 N*m (420 kgf*cm, 30 ft.*lbf)
INSTALL UPPER CENTER PILLAR GARNISH (See INSTALLATION )

Fig 5: Identifying Front Seat Outer Belt Assembly Shoulder Anchor Nut
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH (for Front Passenger Side)
1. Install the floor end of the front seat outer belt assembly RH with the front seat belt anchor base.
  Torque: 41 N*m (420 kgf*cm, 30 ft.*lbf)
  
  Fig 6: Identifying Front Seat Outer Belt Assembly RH Floor End Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Engage the clamp.
3. Connect the connector.
4. Check if the ELR locks.
  NOTE: The check should be performed with the outer belt assembly installed.
  1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
INSTALL LOWER CENTER PILLAR GARNISH (See INSTALLATION )
CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH (for Driver Side)
1. Install the floor end of the front seat outer belt assembly LH with the bolt.
  Torque: 41 N*m (420 kgf*cm, 30 ft.*lbf)
2. Check if the ELR locks.
  NOTE: The check should be performed with the outer belt assembly installed.
  
  Fig 7: Identifying Floor End Of Front Seat Outer Belt Assembly LH With Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
INSTALL LAP BELT OUTER ANCHOR COVER (for Driver Side)
1. Engage the 3 claws and install the lap belt outer anchor cover.
Fig 8: Identifying Lap Belt Outer Anchor Cover Claws
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL LAP BELT OUTER ANCHOR COVER (for Front Passenger Side)
1. Engage the 2 guides.
  
  Fig 9: Identifying Lap Belt Outer Anchor Cover And Guides
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Engage the 2 claws and install the lap belt outer anchor cover.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP (See INSTALLATION )
INSTALL REAR DOOR SCUFF PLATE (See INSTALLATION )

Fig 10: Identifying Lap Belt Outer Anchor Cover Claws
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP (See INSTALLATION )
INSTALL FRONT DOOR SCUFF PLATE (See INSTALLATION )
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
INSPECT SRS WARNING LIGHT
(See DIAGNOSIS SYSTEM )