Front Stabilizer Bar: Removal

REMOVE STABILIZER CONTROL VALVE PROTECTOR (See REMOVAL )
OPEN STABILIZER CONTROL WITH ACCUMULATOR HOUSING SHUTTER VALVE (See REMOVAL )
REMOVE FRONT WHEEL
REMOVE TAILPIPE ASSEMBLY (See REMOVAL )
REMOVE EXHAUST CENTER PIPE ASSEMBLY (See REMOVAL )
DISCHARGE SUSPENSION FLUID PRESSURE (See REMOVAL )
REMOVE FRONT FENDER SPLASH SHIELD SUBASSEMBLY LH (See REMOVAL )
REMOVE FRONT FENDER SPLASH SHIELD SUBASSEMBLY RH (See REMOVAL )
REMOVE NO. 1 ENGINE UNDER COVER SUBASSEMBLY (See REMOVAL )
REMOVE FRONT FENDER APRON SEAL LH (See REMOVAL )
REMOVE FRONT FENDER APRON SEAL REAR LH (See REMOVAL )
REMOVE STABILIZER CONTROL TUBE PROTECTOR
1. Remove the 2 bolts and tube protector.
  
  Fig 1: Locating Stabilizer Control Tube Protector Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
DISCONNECT FRONT NO. 1 STABILIZER CONTROL TUBE ASSEMBLY
1. Remove the 2 union bolts and 2 gaskets, and disconnect the stabilizer control tube.
  
  Fig 2: Locating Front Stabilizer Control Tube Assembly Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
LOOSEN FRONT NO. 1 STABILIZER BRACKET LH
1. Loosen the 2 bolts of the front stabilizer brackets.
  
  Fig 3: Locating Front Stabilizer Brackets Bolts (LH)
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
LOOSEN FRONT NO. 1 STABILIZER BRACKET RH
1. Loosen the 2 bolts of the front stabilizer brackets.
  
  Fig 4: Locating Front Stabilizer Brackets Bolts (RH)
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE FRONT STABILIZER LINK ASSEMBLY LH
1. Remove the 2 bolts, nut and stabilizer link.
  
  Fig 5: Locating Front Stabilizer Link Assembly Bolts And Nut (LH)
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE FRONT STABILIZER LINK ASSEMBLY RH
1. Remove the bolt, nut and stabilizer link.
  HINT:
  
  If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud.
  
  Fig 6: Locating Front Stabilizer Link Assembly Bolts And Nut (RH)
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE FRONT NO. 1 STABILIZER BRACKET LH
1. Remove the 2 bolts and stabilizer bracket from the front frame assembly.
  
  Fig 7: Locating Front Stabilizer Brackets Bolts (LH)
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE FRONT NO. 1 STABILIZER BRACKET RH
1. Remove the 2 bolts and stabilizer bracket from the front frame assembly.
  
  Fig 8: Locating Front Stabilizer Brackets Bolts (RH)
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
DISCONNECT FRONT STABILIZER CONTROL CYLINDER
1. Remove the bolt, washer, nut, and stabilizer control cylinder from the frame assembly.
  
  Fig 9: Locating Front Stabilizer Control Cylinder Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE FRONT STABILIZER BAR
1. Remove the bolt, nut and front stabilizer bar from the stabilizer control arm.
REMOVE FRONT NO. 1 STABILIZER BAR BUSH
1. Remove the 2 stabilizer bar bushes from the front stabilizer bar.
  
  Fig 10: Locating Front Stabilizer Control Arm Bolt And Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE FRONT STABILIZER CONTROL ARM ASSEMBLY
1. Remove the bolt, nut and front stabilizer control arm from the front stabilizer control cylinder.
  
  Fig 11: Locating Front Stabilizer Control Arm Bolt And Nut
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE FRONT NO. 1 SUSPENSION CONTROL BLEEDER PLUG
1. Remove the 2 front suspension control bleeder plugs from the front stabilizer control cylinder.
  
  Fig 12: Locating Front Suspension Control Bleeder Plugs
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002