REAR STABILIZER BAR (for 4WD): Installation

1. Temporarily install the rear stabilizer bar with the identification mark positioned on the left side of the vehicle.

Fig 1: Identifying Mark On Rear Stabilizer Bar

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Temporarily install the rear stabilizer bar bracket LH (front side) with the bolt.

   HINT:

   Loosely tighten the bolt so that the bracket can be moved by hand.

Fig 2: Locating Rear Stabilizer Bar Bracket Bolt LH (Front Side)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Temporarily install the rear stabilizer bar bracket RH (front side) with the 2 bolts.

   HINT:

   Loosely tighten the bolts so that the bracket can be moved by hand.

Fig 3: Locating Rear Stabilizer Bar Bracket Bolts RH (Front Side)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the rear stabilizer bushing (LH side) to the rear stabilizer bar.
   NOTE: Make sure that the cutout of the rear stabilizer bushing is positioned within the range shown in the illustration.

Fig 4: Identifying Rear Stabilizer Bushing Position (LH Side)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the rear stabilizer bushing (RH side) to the rear stabilizer bar.
   NOTE: Make sure that the cutout of the rear stabilizer bushing is positioned within the range shown in the illustration.

Fig 5: Identifying Rear Stabilizer Bushing Position (RH Side)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the rear stabilizer bar bracket LH (rear side) with the 2 bolts.

   Torque: 19 N*m (194 kgf*cm, 14 ft.*lbf) 

Fig 6: Locating Rear Stabilizer Bar Bracket Bolts LH (Rear Side)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the rear stabilizer bar bracket RH (rear side) with the 2 bolts.

   Torque: 19 N*m (194 kgf*cm, 14 ft.*lbf) 

Fig 7: Locating Rear Stabilizer Bar Bracket Bolts RH (Rear Side)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Fully tighten the bolt.

   Torque: 54 N*m (550 kgf*cm, 40 ft.*lbf) 

Fig 8: Locating Rear Stabilizer Bar Bracket Bolts LH (Front Side)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Fully tighten the 2 bolts.

   Torque: 19 N*m (194 kgf*cm, 14 ft.*lbf) 

Fig 9: Locating Rear Stabilizer Bar Bracket RH (Front Side)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the rear stabilizer link assembly LH to the rear shock absorber with coil spring LH with the nut.

   Torque: 39 N*m (400 kgf*cm, 29 ft.*lbf) 

   HINT:

   If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.

   Fig 10: Installing Rear Stabilizer Link Assembly (4WD)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the rear stabilizer link assembly LH to the rear stabilizer bar with the nut.

   Torque: 39 N*m (400 kgf*cm, 29 ft.*lbf) 

   HINT:

   If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.

HINT:

Perform the same procedure as the LH side.

Fig 11: Installing Rear Stabilizer Link Assembly LH To Rear Stabilizer Bar With Nut

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Torque: 103 N*m (1050 kgf*cm, 76 ft.*lbf)