Parking Brake Assembly: Disassembly

HINT:

• Use the same procedures for the RH side and the LH side.
• The procedures listed below are for the LH side.

1. REMOVE REAR WHEEL 
2. REMOVE REAR AXLE SHAFT NUT (for 4WD) 
   NOTE: Perform this procedure only when the No. 1 parking brake shoe hold down spring pin is replaced.

   HINT:

   See REMOVAL .

3. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY (for 2WD)  (See REPLACEMENT )
4. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY (for 4WD)  (See REPLACEMENT )
5. REMOVE REAR DISC  (See INSPECTION )
6. REMOVE NO. 1 PARKING BRAKE SHOE RETURN TENSION SPRING 
   1. Remove the 2 No. 1 parking brake shoe return tension springs.
      Fig 1: Identifying No. 1 Parking Brake Shoe Return Tension Springs

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. SEPARATE NO. 1 PARKING BRAKE SHOE ASSEMBLY 
   1. Remove the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring and No. 2 parking brake shoe hold down spring cup, and separate the No. 1 parking brake shoe assembly from the backing plate.
      Fig 2: Identifying No. 1 Parking Brake Shoe Assembly

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. REMOVE PARKING BRAKE SHOE STRUT 
   1. Remove the parking brake shoe strut and the parking brake shoe strut compression spring.
      Fig 3: Identifying Parking Brake Shoe Strut And Parking Brake Shoe Strut Compression Spring

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
9. SEPARATE NO. 2 PARKING BRAKE SHOE ASSEMBLY 
   1. Remove the No. 1 parking brake shoe hold down spring cup, parking brake shoe hold down spring and No. 2 parking brake shoe hold down spring cup, and separate the No. 2 parking brake shoe assembly from the backing plate.
      Fig 4: Identifying No. 2 Parking Brake Shoe Assembly

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
10. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET 
    1. Remove the parking brake shoe adjusting screw set.
       Fig 5: Identifying Parking Brake Shoe Adjusting Screw Set

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
11. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY 
    1. Separate the No. 2 parking brake shoe return tension spring and remove the No. 1 parking brake shoe assembly.
       Fig 6: Identifying No. 2 Parking Brake Shoe Return Tension Spring And No. 1 Parking Brake Shoe Assembly

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
12. REMOVE NO. 2 PARKING BRAKE SHOE RETURN TENSION SPRING 
    1. Remove the No. 2 parking brake shoe return tension spring from the No. 2 parking brake shoe assembly.
       Fig 7: Locating No. 2 Parking Brake Shoe Return Tension Spring

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
13. REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY WITH PARKING BRAKE SHOE LEVER 
    1. Using needle-nose pliers, separate the No. 3 parking brake cable assembly from the parking brake shoe lever as shown in the illustration.
       NOTE: Be careful not to damage the No. 3 parking brake cable assembly.
       Fig 8: Separating No. 3 Parking Brake Cable Assembly From Parking Brake Shoe Lever

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
14. REMOVE PARKING BRAKE SHOE LEVER 
    1. Remove the C-washer, shim and the parking brake shoe lever from the No. 2 parking brake shoe assembly.
       Fig 9: Removing C-Washer, Shim And Parking Brake Shoe Lever From No. 2 Parking Brake Shoe Assembly

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
15. REMOVE PARKING BRAKE SHOE GUIDE PLATE SET BOLT 
    1. Remove the parking brake shoe guide plate set bolt and the parking brake shoe guide plate.
       Fig 10: Identifying Parking Brake Shoe Guide Plate Set Bolt

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
16. REMOVE NO. 1 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 2WD) 
    1. Remove the No. 1 parking brake shoe hold down spring pin.
       Fig 11: Identifying No. 1 Parking Brake Shoe Hold Down Spring Pin

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
17. REMOVE NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 4WD) 
    1. Remove the No. 2 parking brake shoe hold down spring pin.
       Fig 12: Identifying No. 2 Parking Brake Shoe Hold Down Spring Pin

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
18. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY (for 2WD) 
    NOTE: Perform this procedure only when the No. 2 parking brake shoe hold down spring pin is replaced.

    HINT:

    See ON-VEHICLE INSPECTION .

19. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY (for 4WD) 
    NOTE: Perform this procedure only when the No. 1 parking brake shoe hold down spring pin is replaced.

    HINT:

    See ON-VEHICLE INSPECTION .

20. REMOVE NO. 2 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 2WD) 
    1. Remove the No. 2 parking brake shoe hold down spring pin.
       Fig 13: Identifying No. 2 Parking Brake Shoe Hold Down Spring Pin

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
21. REMOVE NO. 1 PARKING BRAKE SHOE HOLD DOWN SPRING PIN (for 4WD) 
    1. Remove the No. 1 parking brake shoe hold down spring pin.
       Fig 14: Identifying No. 1 Parking Brake Shoe Hold Down Spring Pin

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002