PARKING BRAKE CABLE (for Rear Disc Brake): Removal

CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See AIRBAG SYSTEM ).

HINT:

Use the same procedure for the No. 2 parking brake cable assembly and No. 3 parking brake cable assembly.
The procedure listed below is for the No. 3 parking brake cable assembly.

DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Front Seat Side Airbag)
CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
REMOVE REAR WHEELS
REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)
HINT:

Refer to the instructions for Removal of the front seat assembly (See REMOVAL ).
REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)
HINT:

Refer to the instructions for Removal of the front seat assembly (See REMOVAL ).
REMOVE FRONT SEAT ASSEMBLY RH
HINT:

Perform the same procedure for the LH side.
REMOVE CONSOLE BOX ASSEMBLY
HINT:

Refer to the instructions for Removal of the front console box (See REMOVAL ).
REMOVE NO. 2 BELT ANCHOR REINFORCEMENT SUB-ASSEMBLY (See REMOVAL )
REMOVE NO. 3 BELT ANCHOR REINFORCEMENT SUB-ASSEMBLY (See REMOVAL )
SEPARATE PARKING BRAKE EQUALIZER (See REMOVAL )
REMOVE PARKING BRAKE LEVER ASSEMBLY (See REMOVAL )
REMOVE PARKING BRAKE EQUALIZER (See REMOVAL )
REMOVE PARKING BRAKE CABLE END STOPPER (See REMOVAL )
REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (See REMOVAL )
REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 2ZR-FE) (See REMOVAL )
REMOVE CENTER EXHAUST PIPE ASSEMBLY (for 2AZ-FE) (See REMOVAL )
REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR
1. Remove the 3 nuts and front No. 1 floor heat insulator.
  
  Fig 1: Locating Front No. 1 Floor Heat Insulator Mounting Nuts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR
1. Remove the 2 nuts and front No. 2 floor heat insulator.
  
  Fig 2: Locating Front No. 2 Floor Heat Insulator Mounting Nuts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE PARKING BRAKE LEVER PROTECTOR
1. Remove the parking brake lever protector from the No. 3 parking brake cable assembly.
  
  Fig 3: Identifying Parking Brake Lever Protector
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY
1. Disengage the clamp from the No. 3 parking brake cable assembly.
2. Remove the bolt.
  
  Fig 4: Identifying No. 3 Parking Brake Cable Assembly Clamp And Bolt
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.
  
  Fig 5: Separating No. 3 Parking Brake Cable Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Remove the No. 3 parking brake cable assembly.
  HINT:
  
  Insert an offset wrench (14 mm) at the base of the No. 3 parking brake cable assembly as shown in the illustration to disengage the clip. Pull out the No. 3 parking brake cable assembly from the rear disc brake cylinder assembly.
  
  Fig 6: Removing No. 3 Parking Brake Cable Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. Separate the No. 3 parking brake cable clamp.
  
  Fig 7: Identifying No. 3 Parking Brake Cable Clamp
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Remove the bolt and pull out the No. 3 parking brake cable assembly to the outside of the body.
  
  Fig 8: Removing No. 3 Parking Brake Cable Assembly To Outside Of Body
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
7. Remove the 2 bolts and the No. 3 parking brake cable assembly.
  
  Fig 9: Identifying No. 3 Parking Brake Cable Assembly With Mounting Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE NO. 3 PARKING BRAKE CABLE CLAMP
1. Disengage the 2 claws to remove the No. 3 parking brake cable clamp from the No. 3 parking brake cable assembly.
  
  Fig 10: Locating No. 3 Parking Brake Cable Clamp And Claws
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002