LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2009 >> Camry Base, Automatic >> Repair and Diagnosis >> Restraints >> Passive Restraints >> Seat Belt (Except Hybrid) >> Rear Seat Outer Belt Assembly >> Installation

Rear Seat Outer Belt Assembly: Installation

  1. INSTALL REAR SEAT OUTER BELT ASSEMBLY 
    1. Check the degree of the tilt when the ELR begins to lock.
      1. Check that the belt does not lock at less than 15 degrees of tilt in any direction but locks at over 45 degrees of tilt while gently pulling the belt.
        NOTE: Do not disassemble the retractor.
        Fig 1: Identifying Belt 45 Degrees Tilt Direction
        G04979824Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Align the claw with the seat belt positioning hole and install the rear seat outer belt assembly with the bolt.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

      Fig 2: Aligning Claw With Seat Belt Positioning Hole
      G04979825Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY  (See INSTALLATION )
  3. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (for Reclining Seat Type)  (See INSTALLATION )
  4. INSTALL REAR SEAT SHOULDER BELT HOLE COVER 
    1. Engage the 4 claws and install the rear seat shoulder belt hole cover.
      Fig 3: Engaging Rear Seat Shoulder Belt Hole Cover Claws
      G04979805Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. INSTALL REAR SEAT SHOULDER BELT COVER 
    1. Engage the 4 claws and install the rear seat shoulder belt cover.

      HINT:

      Use the same procedures for the RH side and the LH side.

      Fig 4: Identifying Rear Seat Shoulder Belt Cover Claws
      G04979806Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  6. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side) 
    1. Connect the floor end of the rear seat outer belt assembly with the bolt.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

      NOTE: Do not allow the anchor part of the rear seat outer belt assembly to overlap protruding parts of the floor panel.
      Fig 5: Identifying Rear Seat Outer Belt Assembly Floor End Bolt
      G04979807Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check if the ELR locks.
      NOTE: The check should be performed with the outer belt assembly installed.
      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
  7. CONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side) 
    1. Connect the floor end of the rear seat outer belt assembly with the bolt.

      Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf) 

      NOTE: Do not allow the anchor part of the rear seat outer belt assembly, to overlap protruding parts of the floor panel.
      Fig 6: Identifying Protruding Parts Of Floor Panel
      G04979829Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check if the ELR locks.
      NOTE: The check should be performed with the outer belt assembly installed.
      1. With the belt assembly installed, check that the belt locks when it is pulled out quickly.
  8. INSTALL ROOF SIDE INNER GARNISH LH  (See INSTALLATION )
  9. INSTALL ROOF SIDE INNER GARNISH RH  (See INSTALLATION )
  10. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (for TMC Made)  (See INSTALLATION )
  11. CONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH (for TMMK Made)  (See INSTALLATION )
  12. INSTALL CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH  (See INSTALLATION )
  13. INSTALL. RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY LH (for Reclining Seat Type)  (See REASSEMBLY )
  14. INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY RH (for Reclining Seat Type) 

    HINT:

    Use the same procedures for the RH side and the LH side.

  15. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH  (See INSTALLATION )
  16. INSTALL REAR DOOR SCUFF PLATE LH  (See INSTALLATION )
  17. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH  (See INSTALLATION )
  18. INSTALL REAR DOOR SCUFF PLATE RH  (See INSTALLATION )
  19. INSTALL CENTER SEAT BACK ASSEMBLY (for Reclining Seat Type)  (See INSTALLATION )
  20. INSTALL SEPARATE TYPE REAR SEAT BACK ASSEMBLY LH (for Reclining Seat Type)  (See INSTALLATION )
  21. INSTALL SEPARATE TYPE REAR SEAT BACK ASSEMBLY RH (for Reclining Seat Type)  (See INSTALLATION )
  22. INSTALL REAR SEAT BACK COVER (for Reclining Seat Type) 
  23. INSTALL REAR SIDE SEAT BACK ASSEMBLY LH (for Fold Down Seat Type)  (See INSTALLATION )
  24. INSTALL REAR SIDE SEAT BACK ASSEMBLY RH (for Fold Down Seat Type) 

    HINT:

    Use the same procedures for the RH side and the LH side.

  25. INSTALL SEPARATE TYPE REAR SEAT BACK ASSEMBLY LH (for Fold Down Seat Type)  (See INSTALLATION )
  26. INSTALL SEPARATE TYPE REAR SEAT BACK ASSEMBLY RH (for Fold Down Seat Type)  (See INSTALLATION )
  27. INSTALL REAR SEAT BACK ASSEMBLY (for Fixed Seat Type)  (See INSTALLATION )
  28. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY 
  29. INSTALL REAR SEAT HEADREST ASSEMBLY 
  30. INSTALL REAR SEAT CUSHION ASSEMBLY  (See INSTALLATION )
scientia non olet · About LEMON Manuals