REAR STABILIZER BAR (for 4WD): Installation

1. Temporarily install the rear stabilizer bar with the identification mark positioned on the left side of the vehicle.
   Fig 1: Identifying Rear Stabilizer Bar Mark Location

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Temporarily install the rear stabilizer bar bracket LH (front side) with the bolt.

   HINT:

   Loosely tighten the bolt so that the bracket can be moved by hand.

   Fig 2: Locating Rear Stabilizer Bar Bracket LH Bolt (Front Side)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Temporarily install the rear stabilizer bar bracket RH (front side) with the 2 bolts.

   HINT:

   Loosely tighten the bolts so that the bracket can be moved by hand.

   Fig 3: Identifying Rear Stabilizer Bar Bracket RH & Bolt (Front Side)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the rear stabilizer bushing (LH side) to the rear stabilizer bar.
   NOTE: Make sure that the cutout of the rear stabilizer bushing is positioned within the range shown below.
   Fig 4: Identifying Rear Stabilizer Bushing (LH Side)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the rear stabilizer bushing (RH side) to the rear stabilizer bar.
   NOTE: Make sure that the cutout of the rear stabilizer bushing is positioned within the range shown below.
   Fig 5: Identifying Rear Stabilizer Bushing (RH Side)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the rear stabilizer bar bracket LH (rear side) with the 2 bolts.

   Torque: 19 N*m (194 kgf*cm, 14 ft.*lbf) 

   Fig 6: Identifying Rear Stabilizer Bar Bracket LH (Rear Side)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the rear stabilizer bar bracket RH (rear side) with the 2 bolts.

   Torque: 19 N*m (194 kgf*cm, 14 ft.*lbf) 

   Fig 7: Identifying Rear Stabilizer Bar Bracket RH (Rear Side)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Fully tighten the bolt.

   Torque: 54 N*m (550 kgf*cm, 40 ft.*lbf) 

   Fig 8: Identifying Rear Stabilizer Bar Bracket LH (For Front Side)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Fully tighten the 2 bolts.

   Torque: 19 N*m (194 kgf*cm, 14 ft.*lbf) 

   Fig 9: Locating Rear Stabilizer Bar Bracket RH Bolts (For Front Side)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Install the rear stabilizer link assembly LH to the rear shock absorber with coil spring LH with the nut.

   Torque: 39 N*m (400 kgf*cm, 29 ft.*lbf) 

   HINT:

   If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.

   Fig 10: Identifying Rear Stabilizer Link Assembly With Coil Spring & Nut (For 4WD)

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the rear stabilizer link assembly LH to the rear stabilizer bar with the nut.

   Torque: 39 N*m (400 kgf*cm, 29 ft.*lbf) 

   HINT:

   If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud bolt.

   Fig 11: Identifying Rear Stabilizer Link Assembly LH & Rear Stabilizer Bar

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

Perform the same procedure as the LH side.

Torque: 103 N*m (1050 kgf*cm, 76 ft.*lbf)