Rear No. 2 Seat Assembly: Reassembly

WARNING: This page is about a different car, the 2007 Toyota RAV4. However, it is still accessible from the selected car via links, so may be relevant.

HINT:

Use the same procedures for the RH side and LH side.
The procedures listed below are for the LH side.

INSTALL SEAT LOCK RELEASE BAND
1. Install the band with nut (see Fig 1).
  HINT:
  
  After installing the band, feed it through the seatback frame hole towards the rear of the vehicle.
INSTALL RECLINING LOCK RELEASE BAND
HINT:

Use the same procedures described for the LH side.
INSTALL SEATBACK LOCK CONTROL CABLE ASSEMBLY
1. Install the cable to the seatback frame as shown in the illustration.
  
  Fig 1: Installing Cable To Seatback Frame
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR SEAT RECLINING INNER COVER LH
1. Attach the 2 claws to install the inner cover.
  
  Fig 2: Attaching Claws To Inner Cover
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR SEAT RECLINING INNER COVER RH
HINT:

Use the same procedures described for the LH side.
INSTALL REAR NO. 2 SEATBACK COVER
NOTE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
1. Using hog ring pliers, install the seatback cover to the seatback pad with 3 new hog rings.
2. Install the seatback cover (with pad) to the seatback frame.
  
  Fig 3: Installing Seatback Cover To Seatback Pad With Hog Rings
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Attach the 4 claws to install the 2 headrest supports.
  
  Fig 4: Installing Headrest Supports
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Using hog ring pliers, install 19 new hog rings.
INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH
1. Pass the 2 release bands through the 2 holes in the seatback board carpet.
  
  Fig 5: Installing Hog Rings
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Attach the 9 clips to install the carpet.
  HINT:
  
  Make sure that the release band is not inside the seatback board carpet.
  
  Fig 6: Attaching Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL REAR SEATBACK LOCK CONTROL BEZEL
1. Pass the 2 release bands through the 2 holes in the 2 bezels.
2. Attach the 2 claws to install the 2 bezels.
3. Install the 2 screws.
  
  Fig 7: Installing Rear Seatback Lock Control Bezel
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Install the 4 seatback lock hooks.
INSTALL REAR NO. 2 SEAT HEADREST ASSEMBLY
INSTALL REAR SEAT CUSHION WIRE SUB-ASSEMBLY
1. Install the wire with the nut.
  Torque: 18 N*m (184 kgf*cm, 13 ft.*lbf)
  
  Fig 8: Installing Seatback Lock Hooks
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL SEAT LOCK CONTROL CABLE ASSEMBLY
1. Install the 5 cables to the seat cushion spring as shown in the illustration.
  
  Fig 9: Installing Cables To Seat Cushion Spring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Clamp the cables to the seat cushion spring with 4 new cable ties as shown in the illustration.
  
  Fig 10: Clamping Cables To Seat Cushion Spring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Cut off the 2 cable ties, as shown in the illustration.
  
  Fig 11: Identifying Cut Off Cable
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. Attach the 2 clamps of the cable tie to the seat cushion spring.
INSTALL REAR NO. 2 SEAT CUSHION COVER LH
NOTE:
- Be careful not to damage the cover.
- When installing the hog rings, avoid wrinkling the cover.
  
  Fig 12: Attaching Clamps Of Cable Tie To Seat Cushion Spring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with 5 new hog rings.
  
  Fig 13: Installing Seat Cushion Cover To Seat Cushion Pad With Hog Rings
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Attach the hooks and install the seat cushion cover (with pad) to the seat cushion spring.
  
  Fig 14: Attaching Hooks And Seat Cushion Cover (With Pad) To Seat Cushion Spring
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Attach the 5 hooks.
4. Install the 2 clips.
INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH (See INSTALLATION )

Fig 15: Attaching Hooks
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
REMOVE REAR NO. 2 SEAT CUSHION ASSEMBLY
1. Install the seat cushion to the seatback with the 4 bolts.
  Torque: 42 N*m (428 kgf*cm, 31 ft.*lbf)
  
  Fig 16: Installing Seat Cushion To Seatback With Bolts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Connect the seat lock control cable of the RH side to the seatback as shown in the illustration.
  
  Fig 17: Connecting Seat Lock Control Cable Of RH Side
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Connect the seat lock control cable of the back side to the seat cushion as shown in the illustration.
4. Close the seat cushion cover and install the 2 clips.
  
  Fig 18: Connecting Seat Lock Control Cable Of Back Side
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL NO. 1 REAR SEAT RECLINING COVER LH
1. Attach the 5 claws to install the cover.
2. Install the 2 screws.
  
  Fig 19: Installing No. 1 Rear Seat Reclining Cover With Screw
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL NO. 2 REAR SEAT RECLINING COVER LH
1. Attach the clip and 5 claws to install the cover.
2. Install the 2 screws.
  
  Fig 20: Installing No. 2 Rear Seat Reclining Cover With Screw
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002