LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2008 >> FJ Cruiser RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 237 (Automatic Transmission - U340E) >> Transmission Control Cable Assembly >> Installation

Transmission Control Cable Assembly: Installation

WARNING: This page is about a different car, the 2008 Toyota Yaris. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY 
    1. Install the control cable onto the control shaft lever with the nut.

      Torque: 12 N*m (122 kgf*cm, 9 ft.*lbf) 

      Fig 1: Identifying Nut And Control Cable
      G04831146Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Fix the control cable onto the control cable bracket with a new clip.
    3. Connect the control cable to the clamp.
      Fig 2: Identifying Control Cable Support
      G04831145Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. Install the control cable with the 3 nuts.

      Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf) 

      Fig 3: Identifying Nuts And Control Cable
      G04831147Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    5. Turn the nut of the control cable and push in the lock.
      Fig 4: Identifying Nut
      G04831151Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    6. Install the control cable onto the shift lever retainer.
      NOTE:
      • Install the cable with the protruding portion of the cable outer facing upward.
      • After installing, check that the lock of the cable outer is protruding beyond portion A-A, as shown in the illustration.
        Fig 5: Identifying Shift Lever Retainer
        G04831152Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    7. Connect the control cable to the shift lever.
      NOTE: Connect the control cable so that the adjusting mechanism lock of the control cable is installed on the left side of the vehicle.
      Fig 6: Identifying Control Cable
      G04831143Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR 
    1. Install floor heat insulator with the 2 bolts and the nut.

      Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf) 

      Fig 7: Identifying Bolts, Nut And Floor Heat Insulator
      G04831142Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL FRONT EXHAUST PIPE ASSEMBLY  (See INSTALLATION )
  4. CONNECT OXYGEN SENSOR CONNECTOR 
    1. Insert the oxygen sensor connector toward the room side, through the hole in the floor panel, and then install the grommet.
      2. Fig 8: Identifying Oxygen Sensor Connector
      G04831141Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Connect the oxygen sensor connector.
  5. INSTALL AIR CLEANER BRACKET  (See INSTALLATION )
  6. INSTALL AIR CLEANER ASSEMBLY  (See INSTALLATION )
  7. INSTALL BATTERY TRAY 
  8. INSTALL BATTERY  (See INSTALLATION )
  9. INSPECT SHIFT LEVER POSITION (See  ON-VEHICLE INSPECTION   ) 
  10. ADJUST SHIFT LEVER POSITION (See  ADJUSTMENT   ) 
  11. INSTALL REAR CONSOLE BOX ASSEMBLY  (See INSTALLATION )
  12. INSTALL CONSOLE BOX CARPET  (See INSTALLATION )
  13. INSTALL REAR CONSOLE BOX COVER (for Hatchback)  (See INSTALLATION )
  14. INSTALL REAR UPPER CONSOLE PANEL SUBASSEMBLY (for Sedan)  (See INSTALLATION )
  15. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY (for Sedan)  (See INSTALLATION )
  16. INSTALL CENTER LOWER INSTRUMENT PANEL FINISH PANEL (for Sedan)  (See INSTALLATION )
  17. CHECK FOR EXHAUST GAS LEAKAGE 
scientia non olet · About LEMON Manuals